Contact Us

OPA335AID

Brand: Texas Instruments
Texas Instruments OPA335AID is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA335AID — Power Management & Signal Chain | Superb Automation

OPA335AID

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA335AID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA335AID: zero-drift CMOS operational amplifier with 5 microvolt offset and 2 MHz bandwidth in an 8-pin SOIC

OPA335AID is a zero-drift CMOS operational amplifier that keeps 5 microvolts of offset while reaching 2 MHz of gain bandwidth and 50 milliamps of output current in a SOIC body of 8 pins. The AID suffix is the 8-pin SOIC, the non-shutdown single in the family; the shutdown version is the OPA334 in SOT-23-6. Offset is 1 microvolt typical and 5 microvolts maximum, drift is 0.05 microvolts per degree maximum, gain bandwidth is 2 MHz, slew rate is 1.6 volts per microsecond and the output can source or sink 50 milliamps, so this is a chopper that can also drive a converter's input capacitance directly.

Order code and package

Order codeOPA335AID
Functionzero-drift CMOS operational amplifier, single supply
PackageSOIC, 8 pins, body code D
Supply range+2.7 V to +5.5 V, dual plus or minus 1.35 V to plus or minus 2.75 V
Supply current285 microamps typical, 350 microamps maximum
Gain bandwidth2 MHz
Slew rate1.6 volts per microsecond
Offset1 microvolt typical, 5 microvolts maximum
Drift0.02 microvolts per degree typical, 0.05 microvolts per degree maximum
Output current50 milliamps short circuit
Input common mode100 millivolts below the negative rail to 1.5 V below the positive rail
DatasheetSBOS245D, revision of July 2003

Electrical parameters that decide the application

Power-supply rejection1 microvolt per volt typical, 2 microvolts per volt maximum over temperature
Common-mode rejection110 dB minimum, 130 dB typical
Open-loop gain110 dB minimum, 130 dB typical
Input bias current70 picoamps typical, 200 picoamps maximum, 1 nanoamp over temperature
Input offset current120 picoamps typical, 400 picoamps maximum
Noise from 0.01 to 10 Hz1.4 microvolts peak to peak
Current noise20 femtoamps per root hertz at 10 Hz
Input capacitance1 picofarad differential, 5 picofarads common mode
Junction rangeminus 40 to plus 125 C

Points to check before this part goes on a BOM

5 microvolts maximum is 0.065 of a bit at 16 bits on a 5 V range, so the part is not the accuracy term in any converter chain available today. The value of the guarantee is that it holds over temperature without a trim: drift of 0.05 microvolts per degree over 165 degrees is 8 microvolts, which is still below one hundredth of a 16 bit bit, so nothing in the channel needs to be re-calibrated after the board is built.

2 MHz of gain bandwidth on 350 microamps is the reason this order code exists in a family full of 350 kHz parts. At a gain of 100 the closed loop corner is 20 kHz, so a channel that scans a multiplexer at 20 kSPS has enough bandwidth, and 1.6 volts per microsecond supports a 2 V peak to peak signal to about 127 kHz before the slew rate takes over. The two limits are a decade apart, which is a comfortable ratio.

The input is not rail to rail at the top. The common mode stops 1.5 V below the positive rail, so on a 5 V supply the ceiling is 3.5 V and a high side current sense at 4.5 V is outside the window. This is the one specification that catches people who assume every chopper is rail to rail, and it is the reason the family pairs this part with the OPA333 for high side work.

50 milliamps of short circuit current and a 1.6 volt per microsecond slew rate together let this amplifier drive a 1 kilohm load to within the output swing without a buffer. In a multiplexed 16 bit system that removes a stage and its offset, which is worth more than the amplifier's own 5 microvolts. The output stage is still current limited, so a 100 ohm load is outside what the part should be asked to do.

1.4 microvolts peak to peak from 0.01 to 10 Hz is where the chopper noise lives. On a 16 bit converter that is 18 thousandths of a bit, so the flicker floor is below the converter resolution and the channel can average down to the reference noise. Compare a trimmed bipolar part at 1 microvolt per degree of drift: the chopper wins on drift and loses on noise density above a few kilohertz, which is where the input capacitance and the sampling of the converter start to matter.

1 nanoamp of bias current over temperature through a 100 kilohm source is 100 microvolts, twenty times the offset. The room temperature figure of 200 picoamps is more representative of a board at 25 C, where the error is 20 microvolts, four times the offset. As with every chopper, the offset is so small that the bias current and the source impedance, not the amplifier, decide the usable resolution.

Where this order code fits

Precision transducer conditioning, electronic scales, medical instrument front ends and any channel that needs a chopper with real bandwidth use this part. The 50 milliamp output also lets it drive a 1 kilohm load or a switched capacitor input without a buffer, which is unusual for a zero-drift amplifier. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is the OPA335 input rail to rail? No. It reaches 100 millivolts below the negative rail but stops 1.5 V below the positive rail, so on a 5 V supply the input ceiling is 3.5 V and a high side sense near the rail needs a different part.

How much current can this amplifier deliver? 50 milliamps of short circuit current, which is enough to drive a 1 kilohm load to the output swing and to drive a switched capacitor input directly. A 100 ohm load is beyond what the part is specified for.

What is the difference between the OPA335 and the OPA334? The OPA334 is the same amplifier with a shutdown pin in SOT-23-6, and the OPA335 is the version without shutdown in SOT-23-5 or SOIC. Both are specified over minus 40 to plus 125 C.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.