OPA244UA
Product Specifications
OPA244UA
Texas Instruments — Power Management & Signal Chain
Product Overview
The OPA244UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
OPA244UA: micropower single-supply operational amplifier with a 430 kHz gain bandwidth in an 8-pin SOIC
OPA244UA is a single operational amplifier that draws 50 microamps and reaches 430 kHz of gain bandwidth, with an output that swings to within 0.9 V of the positive rail in a SOIC body of 8 pins. The UA suffix is the 8-pin SOIC body, with a junction to ambient figure of 150 C per watt against 200 C per watt for the SOT-23-5. The amplifier works from 2.6 V to 36 V, draws 50 microamps typical and 60 microamps maximum at 25 C, reaches 430 kHz of gain bandwidth, and has the unusual property of an asymmetric slew rate: 0.16 volts per microsecond rising and 0.1 volts per microsecond falling.
Order code and package
| Order code | OPA244UA |
| Function | micropower single operational amplifier, unity gain stable |
| Package | SOIC, 8 pins, body code D |
| Supply range | 2.6 V to 36 V, minimum operating 2.2 V |
| Supply current | 50 microamps typical, 60 microamps maximum at 25 C, 70 microamps over temperature |
| Gain bandwidth | 430 kHz |
| Slew rate | 0.16 volts per microsecond rising, 0.1 volts per microsecond falling |
| Input common mode | 0 V to 0.9 V below the positive rail |
| Output swing | 0.2 V above the negative rail, 0.9 V below the positive rail |
| Settling | 150 microseconds to 0.01 percent on a 10 V step |
| Junction range | minus 40 to plus 85 C, operating to plus 125 C |
| Datasheet | OPA244, OPA2244, OPA4244 family document from Burr-Brown |
Electrical parameters that decide the application
| Offset | 0.7 millivolts typical, 1.5 millivolts maximum, 2 millivolts over temperature |
| Offset drift | 2 microvolts per degree typical, 4 microvolts per degree maximum |
| Input bias current | 10 nanoamps typical, 25 nanoamps maximum |
| Input offset current | 1 nanoamp typical, 10 nanoamps maximum |
| Voltage noise | 22 nanovolts per root hertz at 1 kHz, 0.4 microvolts peak to peak from 0.1 to 10 kHz |
| Current noise | 40 femtoamps per root hertz at 1 kHz |
| Common-mode rejection | 84 dB minimum, 98 dB typical |
| Open-loop gain | 86 dB minimum, 106 dB typical |
| Power-supply rejection | 5 microvolts per volt typical, 50 microvolts per volt maximum |
| Thermal resistance | 150 C per watt in SOIC, 200 C per watt in SOT-23-5 |
Points to check before this part goes on a BOM
The slew rate is not symmetric, and that is a specification rather than a tolerance. Rising the output is limited to 0.16 volts per microsecond and falling it to 0.1 volts per microsecond, so a bipolar pulse comes out with a slower trailing edge. On a 1 V peak to peak sine the positive limit is 51 kHz and the negative limit 32 kHz, so a 40 kHz square wave arrives with a skewed duty cycle even though the 430 kHz gain bandwidth suggests far more headroom.
1.5 millivolts of maximum offset is 1.2 least significant bits on a 12 bit converter at 5 V, and 2 millivolts over temperature is 1.6 bits. That is a workable number for a 10 bit channel and a poor one for a 16 bit channel, where a bit is 76 microvolts and the offset alone is 20 bits. This part is a micropower part, not a precision part, and the two are usually confused when a BOM is copied from an older board.
The input common mode starts at the negative rail, which is the useful half of a single-supply amplifier. A low side shunt, a single cell terminal or a ground referenced thermistor all sit inside the window, but the top of the window is 0.9 V below the positive rail, so a high side sense at 4.5 V on a 5 V board is outside the specified range and the output will not follow it.
150 microseconds to 0.01 percent on a 10 V step is 15 microseconds per volt, and it is the settling figure that decides whether this amplifier can scan a multiplexer. A 100 kSPS converter gives 10 microseconds per channel, so the amplifier needs ten times that and the scan rate has to drop to about 6 kSPS, or the channel has to be a DC one that is allowed to settle between readings.
50 microamps typical and 70 microamps maximum over temperature is 613 milliamp hours over a year at the maximum figure. On a 3 V rail that is 210 microwatts, which is small enough for a coin cell product that wakes up once a minute, and large enough that eight channels of it would dominate a 500 microamp standby budget.
Bias current is 25 nanoamps maximum, so a 200 kilohm source contributes 5 millivolts and a 20 kilohm source contributes 500 microvolts. The offset and the bias error are the same size at about 20 kilohms of source resistance, which is the crossover point where the amplifier stops being the limiting error and the network in front of it takes over.
Where this order code fits
Portable instrument front ends, 4 to 20 milliamp receivers, battery gauges and low duty cycle sensor channels use this part when the current budget is tens of microamps and the signal is slower than a few kilohertz. The ground sensing input makes it a natural fit for a low side shunt or a single cell voltage measurement. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Does the OPA244 run from a 3 V rail without a negative supply? Yes. The specified range starts at 2.6 V and the minimum operating voltage is 2.2 V, and the input common mode includes the negative rail, so ground referenced signals work from a single 3 V supply.
Why does the datasheet list two slew rates? Because the output stage is asymmetric. Rising is 0.16 volts per microsecond and falling is 0.1 volts per microsecond, so a bipolar waveform is limited by the slower direction and the two figures are not interchangeable.
What is the settling time to 12 bit accuracy? About 150 microseconds to 0.01 percent on a 10 V step. A 12 bit settling target is close to the 0.01 percent figure, so a multiplexed channel behind this amplifier should be clocked at a few thousand samples per second.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.