Contact Us

OPA241PA

Brand: Texas Instruments
Texas Instruments OPA241PA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

OPA241PA — Power Management & Signal Chain | Superb Automation

OPA241PA

Texas Instruments — Power Management & Signal Chain

Product Overview

The OPA241PA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

OPA241PA: micropower single-supply operational amplifier drawing 25 microamps in an 8-pin plastic DIP

OPA241PA is a single operational amplifier built for 5 V single-supply work at 25 microamps of quiescent current, with offset trim pins brought out in a PDIP body of 8 pins. The PA suffix is the 8-pin plastic DIP body, and the trim pins on pins 1 and 5 exist only on the single versions, so this order code is the one in the family that can be nulled in hardware. Quiescent current is 25 microamps, the offset window at 5 V is 50 microvolts typical and 250 microvolts maximum, and the gain bandwidth product is 35 kHz, which is the number that decides what this amplifier can and cannot do.

Order code and package

Order codeOPA241PA
Functionmicropower single operational amplifier, unity gain stable
PackagePDIP, 8 pins, body code P
Supply range2.7 V to 36 V total, or plus or minus 1.35 V to plus or minus 18 V
Supply current25 microamps per amplifier
Gain bandwidth35 kHz
Slew rate0.01 volts per microsecond
Output swingwithin 50 millivolts of either rail
Offset trimpins 1 and 5, single versions only
Input common mode200 millivolts below the negative rail
Junction rangeminus 40 to plus 85 C
DatasheetSBOS075A, revision of June 2024

Electrical parameters that decide the application

Offset at 25 C50 microvolts typical, 250 microvolts maximum on the OPAx241
Offset over temperature100 microvolts typical, 400 microvolts maximum
Offset drift0.4 microvolts per degree
Input bias current4 nanoamps typical, 20 nanoamps maximum, 25 nanoamps over temperature
Voltage noise65 nanovolts per root hertz at 1 kHz, 1.7 microvolts peak to peak from 0.1 to 10 Hz
Common-mode rejection124 dB
Open-loop gain128 dB
Power-supply rejection3 microvolts per volt typical, 30 microvolts per volt maximum
Output currentshort circuit limited to about 4 milliamps
Offset trim rangeenough to null the 250 microvolt window from a single 8-pin body

Points to check before this part goes on a BOM

35 kHz of gain bandwidth is the whole story. At a gain of 100 the closed loop corner is 350 Hz, and a 10 Hz signal at that gain is already a decade down from the corner. A channel that samples a thermocouple four times a second is fine; a channel that has to follow a 1 kHz vibration is not, and no amount of external gain fixes a 350 Hz closed loop bandwidth because the open loop gain has to be spent on the gain itself.

Slew rate is 0.01 volts per microsecond, which is 10 millivolts per microsecond. On a 1 V peak to peak sine the limit is 10 millivolts per microsecond divided by two pi times 0.5 V, about 3.2 kHz. That is a factor of ten below the 35 kHz gain bandwidth, so the amplifier is slew limited at a tenth of its small signal bandwidth, and any step larger than a few hundred millivolts gets a visible ramp.

25 microamps over a year is 219 milliamp hours, which is what makes this part a standby choice. On a 5 V rail the drain is 125 microwatts, and the same figure over the minus 40 to plus 85 C range is what the datasheet guarantees rather than a typical number taken at 25 C. A board that budgets the whole standby chain at 10 microamps cannot use this amplifier, and a board with a 1 milliamp budget can afford forty of them.

The offset is honest over temperature. The 250 microvolt window at 25 C becomes 400 microvolts over the industrial range, and the 0.4 microvolt per degree drift contributes 50 microvolts of that, so most of the widening is in the initial distribution rather than in drift. Trimming at 25 C with the pins provided therefore holds, because the drift term after trim is only 50 microvolts across 125 degrees.

The output comes within 50 millivolts of either rail, which is what lets a 5 V single supply drive an ADC that measures 0 to 5 V. At the bottom end 50 millivolts is 41 least significant bits on a 12 bit converter at 5 V, so a true zero reading needs either a small negative supply or a resistor to the negative rail. At the top end the same 50 millivolts is the headroom the amplifier needs before it clips.

20 nanoamps of bias current through a 100 kilohm source is 2 millivolts, which is eight times the 250 microvolt offset. The amplifier is only as good as the impedance in front of it, and a 1 megohm thermistor divider spends 20 millivolts of the reading on bias current. Keeping the source under 10 kilohms holds the bias error at 200 microvolts, which is the same order as the offset and the reason the datasheet pairs a micropower amplifier with a low impedance sensor.

Where this order code fits

Standby rails, battery monitors, thermistor and thermocouple front ends, and 4 to 20 milliamp loop receivers use this part because a 25 microamp drain survives a decade on a lithium cell. It is also the standard choice where a 5 V board has to measure a slow sensor and the offset budget is a few hundred microvolts. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the How to Reduce Component Cost page.

Questions buyers ask

What is the difference between the OPA241 and the OPA251 in the same datasheet? The OPA241 is the version optimized for a 5 V supply and the OPA251 for plus or minus 15 V. The offset window, the drift and the input range follow the rail: the OPA251 offset is 100 microvolts typical and 130 microvolts maximum over temperature.

Can this amplifier drive a 12 bit converter directly? Only for slow signals. At 35 kHz gain bandwidth and 0.01 volts per microsecond the settling to a bit is tens of microseconds, so it suits a converter running at a few thousand samples per second and not a 100 kSPS part.

Do the trim pins have to be used? No. They exist on the single versions so a 250 microvolt window can be nulled, and leaving pins 1 and 5 unconnected is the normal case when the offset budget is loose.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Component Lead Time Solutions page sets out the checks that keep a substitute from failing on the bench.