OPA171AID
Product Specifications
OPA171AID
Texas Instruments — Power Management & Signal Chain
Product Overview
The OPA171AID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
OPA171AID: 36 V single supply general purpose operational amplifier with rail to rail output in an 8-pin SOIC
OPA171AID is a single 36 volt operational amplifier with 3 MHz bandwidth, 475 microamps of supply current and rail to rail output in a SOIC body of 8 pins. The OPA171 takes a 2.7 V to 36 V supply, which covers a 24 V industrial rail and a 5 V logic rail with the same part number. Gain bandwidth is 3 MHz, quiescent current is 475 microamps per amplifier, input noise is 14 nanovolts per root hertz, drift is 0.3 microvolts per degree C typical, and the output swings to both rails. The input range includes the negative rail and reaches within 2 V of the positive rail at full performance.
Order code and package
| Order code | OPA171AID |
| Function | single general purpose operational amplifier, 36 V supply |
| Package | SOIC, 8 pins, body code D |
| Supply range | 2.7 V to 36 V, or plus or minus 1.35 V to plus or minus 18 V |
| Gain bandwidth | 3 MHz |
| Quiescent current | 475 microamps per amplifier |
| Input noise | 14 nanovolts per root hertz |
| Offset drift | 0.3 microvolts per degree C typical |
| Input bias current | 8 pA |
| Output | rail to rail |
| Datasheet | SBOS516 revision H, OPA171, OPA2171 and OPA4171 family |
Electrical parameters that decide the application
| Common mode rejection | 120 dB typical |
| Input range | includes the negative rail, and 100 mV below it, within 2 V of the positive rail at full performance |
| Capacitive load | stable to 300 pF |
| Phase reversal | none on input signals beyond the rails |
| Temperature range | minus 40 to plus 125 C |
| RFI | filtered inputs |
| Supply headroom | the output reaches the rails, the input does not reach the positive rail at full performance |
| Package options | 5-pin SOT-23, 8-pin SOIC and 14-pin TSSOP in the family |
| Grades | A grade and standard grade, with the A grade tighter on offset |
| Family | single, dual and quad share the specification |
Points to check before this part goes on a BOM
The input range is the specification that catches people out. The common mode range includes the negative rail and reaches 100 mV below it, but within 2 V of the positive rail the part still works with reduced performance. On a 24 V rail that puts the clean range up to 22 V, and a high side current sense at 23 V is inside the part but outside its full performance window.
14 nanovolts per root hertz over a 10 kHz band is 1.4 microvolts RMS. Against a 0.3 microvolt per degree C drift over 125 degrees, which is 37 microvolts, the drift dominates a direct current measurement and the noise dominates a wideband one, so the two figures answer different applications.
3 MHz at a gain of 100 leaves 30 kHz of closed loop bandwidth, which suits a 1 kHz control loop with a decade of margin. The same amplifier at a gain of 1000 leaves 3 kHz, and a circuit that needs more has to split the gain across two stages rather than expect the part to do it.
475 microamps per amplifier is low for a 36 V part and it is achieved with a CMOS input, which is why the bias current is 8 pA. That combination is what makes the part usable on a high impedance bridge with a 24 V excitation without a second amplifier for buffering.
Stability to 300 pF of load capacitance is a specification worth using rather than a margin to exceed. A cable or a sample and hold stage beyond that needs a series resistor at the output, and the resistor value interacts with the loop, so the 300 pF figure is the boundary at which the compensation is still guaranteed.
The 36 V ceiling covers a 24 V rail with margin for a transient, and it also covers a plus or minus 15 V supply. That range is why one part number appears in 5 V, 12 V and 24 V projects, and why a repair organisation can hold a single reel for all three.
Where this order code fits
24 V industrial signal conditioning, current sense amplifiers on high side shunts, bridge and strain gauge front ends and transducer interfaces use this part, because the 36 V ceiling removes the need for a separate high voltage amplifier on a 24 V loop. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Can this run directly from a 24 V industrial rail? Yes. The supply range reaches 36 V, and the input range covers the full rail except the top 2 V where the performance is reduced. A 24 V rail has 12 V of supply margin.
Is the input rail to rail as well as the output? No. The output is rail to rail, the input includes the negative rail and reaches within 2 V of the positive rail at full performance, which is the limit to check on a high side measurement.
What is the difference between the A grade and the standard grade? The offset selection. Both share the 3 MHz bandwidth, the 14 nanovolt noise and the 475 microamp supply current, and the A grade is tighter on the direct current error.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Pin to Pin Cross Reference page sets out the checks that keep a substitute from failing on the bench.