Contact Us

MC33063ADR

Brand: Texas Instruments
Texas Instruments MC33063ADR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

MC33063ADR — Power Management & Signal Chain | Superb Automation

MC33063ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The MC33063ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

MC33063ADR: 1.5 A switch mode converter controller in an 8-pin SOIC, rated minus 40 to plus 85 C

MC33063ADR is a self contained switching regulator controller with an internal 1.5 A switch, an oscillator and a 1.25 V reference in a SOIC body of 8 pins. The MC33063A carries every block needed for a simple converter on one die: a temperature compensated 1.25 V reference, a comparator, an oscillator, a PWM latch with cycle by cycle current limit, a driver and a 1.5 A output switch. The input range is 3 V to 40 V, buck, boost and inverting topologies all follow from the same eight pins, and this A suffix code is the wide temperature grade at minus 40 to plus 85 C.

Order code and package

Order codeMC33063ADR
Functionswitching regulator controller with an internal output switch
PackageSOIC, 8 pins, body code D
Input range3 V to 40 V
Switch current1.5 A peak
Oscillatorup to 100 kHz, 33 kHz typical with a 1 nF timing capacitor
Reference1.25 V, 2 percent, from 1.225 V to 1.275 V
Topologiesbuck, boost and inverting from the same pinout
Temperature grademinus 40 to plus 85 C
Comparator threshold1.25 V with 1.4 mV to 5 mV of line regulation over the input range
Current limit sense250 mV to 350 mV, 300 mV typical
DatasheetSLLS636 revision N, December 2004 revised January 2015

Electrical parameters that decide the application

Oscillator frequency24 kHz to 42 kHz with a 1 nF timing capacitor and pin 5 at ground, 33 kHz typical
Charge current24 to 42 microamps, 35 microamps typical
Discharge current140 to 260 microamps, 220 microamps typical
Discharge to charge ratio5.2 to 7.5, 6.5 typical
Switch saturation, Darlington1.0 V typical and 1.3 V maximum at 1 A
Switch saturation, non-Darlington0.45 V typical and 0.7 V maximum at 1 A with a forced beta of 20
Supply current4 mA maximum with the oscillator running
Thermal resistance97 C per watt in the 8-pin SOIC
Comparator input bias20 nA typical, 400 nA maximum
Output switch leakage0.01 microamps typical, 100 microamps maximum at 40 V

Points to check before this part goes on a BOM

The 1.5 A figure is a peak switch current, not an output current. In a buck converter the switch carries the inductor current, so a 5 V output at 1 A needs an inductor rated above 1.3 A once ripple is counted, and in a boost the same switch sees the input current, which is larger than the output current by the voltage ratio.

Switch saturation is the loss that decides the thermal answer. In the Darlington configuration the drop at 1 A is 1.0 V typical and 1.3 V maximum, so a switch carrying 1 A for 50 percent of the time dissipates 0.65 W, and the SOIC body at 97 C per watt adds 63 C. The non-Darlington arrangement with 0.45 V cuts that in half and is the configuration to use above about 300 mA.

Current limit is set by a sense resistor against a 300 mV nominal threshold with a 250 mV to 350 mV spread. A 0.33 ohm resistor therefore limits anywhere between 0.76 A and 1.06 A, a plus or minus 15 percent band that has to be compared against the inductor saturation current rather than against the load.

There is no undervoltage lockout and no thermal shutdown in this part. At power up the switch can run at whatever duty the comparator asks for while the input is still rising, and the only protection is the current limit, so a board that needs a clean start sequence has to add an external enable or a supply supervisor.

The oscillator sets the switching frequency and the maximum duty cycle together. With the discharge to charge current ratio of 6.5, the off time is fixed by the timing capacitor and the duty cycle falls out of the ratio between that off time and the period, which is why this part cannot reach a duty above roughly 86 percent and a 12 V to 3.3 V ratio at 40 kHz is close to the practical ceiling.

Saturation voltage is specified at 25 C conditions with a 1 A pulse, and it rises with temperature. A board that relies on 1.0 V at 1 A in a 70 C ambient should be checked against the typical curves, because the thermal loop through the switch resistance is the mechanism that limits output current at high ambient.

The reference tolerance is 2 percent at 25 C and the comparator adds its own offset, so a 5 V output built from the internal reference and a divider lands within about 3 percent before the divider tolerance is counted. Boards that need better use an external reference into the comparator input and leave the internal node alone.

Where this order code fits

Telecom line cards, industrial human machine interfaces, portable instruments and 24 V or 48 V to 5 V housekeeping rails use this part, because it needs no external controller and starts from a rail that would destroy a low voltage regulator. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

What is the difference between MC33063ADR and MC34063ADR? The temperature grade and nothing else. MC33063A is characterised from minus 40 C to plus 85 C, MC34063A from 0 C to 70 C, both on the same die and in the same package.

How much output current can this part deliver at 5 V from 12 V? It depends on the switch duty and the inductor. The switch is rated 1.5 A peak, so a buck at 500 mA to 700 mA output is realistic with a 1 A inductor, and the thermal limit in the SOIC body arrives before the current limit does.

Does it need a heatsink? No, and it cannot take one. The SOIC body is 97 C per watt, so the loss has to be kept under about 0.7 W for a 70 C rise, which is the real constraint on output current.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Reduce Component Cost page sets out the checks that keep a substitute from failing on the bench.