Contact Us

LM324ADR

Brand: Texas Instruments
Texas Instruments LM324ADR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM324ADR — Power Management & Signal Chain | Superb Automation

LM324ADR

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM324ADR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM324ADR: the A grade quad op amp on a reel, three millivolts at room

LM324ADR is the A grade of the quad operational amplifier in the fourteen pin small outline body, on a 2500 piece reel, from 0 to plus 70 degrees. Four amplifiers, a supply range that starts at 3 volts, an input range that includes ground, and an output that swings to within a few millivolts of ground on a light load.

The family is the default quad amplifier of the last forty years, and the A sort is the version to buy when the offset has to stay inside a few millivolts without a trim. The B versions that came later are tighter still, drop in compatible, and worth comparing against this one when a new build is being released rather than an old one replenished.

The A sort against the plain sort

The plain LM324 holds 3 millivolts typical and 7 millivolts maximum at 25 degrees, widening to 9 over the window. The A sort holds 2 millivolts typical and 3 millivolts maximum, widening to 5. On a 5 volt rail that is 0.06 percent of full scale at room and 0.1 percent over the window, which is enough for a sensor front end with a gain of ten and not enough for a precision instrument without a trim.

Input bias current is 15 nanoamps typical and 100 maximum at room, widening to 200 over the window. That is a bipolar input, not a CMOS one, so a 1 megaohm source sees 100 millivolts of error at room and 200 at the extremes. The amplifier is comfortable with source impedances in the tens of kilo ohms and needs a bias current compensation resistor above that.

Orderable codeLM324ADR
Amplifiers per body4, independent
BodySOIC, 14 pins
Carrierlarge tape and reel, 2500 pieces
Reel diameter330 millimetres
Tape width12.4 millimetres
Pocket6.4 by 5.2 millimetres, 2.1 millimetres deep
Pitch8 millimetres
Offset at 25 degrees2 millivolts typical, 3 maximum
Offset over the window5 millivolts maximum
Input bias current at 25 degrees15 nanoamps typical, 100 maximum
Common mode rangeground to 1.5 volts below the positive rail
Large signal gain25 volts per millivolt minimum, 100 typical
Gain bandwidth product1.2 megahertz
Slew rate0.5 volts per microsecond
Supply current, four amplifiers0.7 milliamps typical, 1.2 maximum at 5 volts
Temperature window0 to plus 70 degrees

The 1.2 megahertz that sets the whole application

A gain bandwidth product of 1.2 megahertz means the closed loop bandwidth is 1.2 megahertz divided by the noise gain. At a gain of ten the bandwidth is 120 kilohertz, at a gain of a hundred it is 12 kilohertz. The slew rate of 0.5 volts per microsecond sets a second limit: a 5 volt step takes 10 microseconds, which corresponds to a full power bandwidth of about 16 kilohertz.

Those two numbers put the part in its place. It is a slow, cheap, robust amplifier for sensing, filtering, buffering and driving, and it is not an audio amplifier with 20 kilohertz of flat response at 5 volts, and it is not a video amplifier at all. A circuit that needs either should not be built around this family.

The output stage is the other limitation. On a 30 volt supply with a 10 kilo ohm load the output reaches 26 volts, and with a 2 kilo ohm load it reaches the positive rail minus 1.5 volts. On a 5 volt supply with a 2 kilo ohm load the swing is roughly 0.1 to 3.5 volts, so a rail to rail requirement is not met by this part at low supply.

Four amplifiers and the current budget

The whole body draws 0.7 milliamps typical and 1.2 maximum at 5 volts, and 1.4 to 3 milliamps at 30 volts. That is 175 microamps per amplifier at the low end, which is what makes a quad package attractive in a battery instrument: four sensing channels for less than a milliamp.

Two cautions belong with that number. The quiescent current is specified with the outputs at mid supply and no load, so an amplifier that swings close to a rail draws more. And the short circuit current is 40 to 60 milliamps, so a channel that is accidentally loaded to ground heats the whole body and shifts the offset of the other three.

Thermal coupling inside the package is real at this current. The junction temperature rise for four amplifiers driving loads can be tens of degrees, and a 5 millivolt offset window that is quoted at 25 degrees ambient is not the window at a 60 degree junction.

Why the A sort on a reel

A 2500 piece reel is the production carrier and the A sort is the grade that keeps a line's test limits stable. The pocket and tape dimensions, 6.4 by 5.2 by 2.1 millimetres on 12.4 millimetre tape at 8 millimetre pitch, are the same as the other fourteen pin small outline parts on the board, so no extra feeder setup is needed.

Our amplifier cross reference page keeps the notes on the dual and quad parts that share this pinout, and the medical device components page covers what a medical build looks for when the same amplifier is used in a patient connected front end, where the long term availability matters as much as the offset.

One sourcing note. Newer B versions of this family carry a 600 microvolt typical offset, a 3 volt minimum supply and integrated EMI filtering, and they are drop in compatible. A bill of materials that still names the A sort should be checked against the B version before the next release, because the B part is usually both tighter and cheaper.

Filter and buffer cases

A 1.2 megahertz amplifier is comfortable in a two pole active filter at a few kilohertz of corner frequency, where the loop has twenty times the gain it needs and the offset window sets the output error. It is not comfortable in a filter at a hundred kilohertz, where the same amplifier has a gain of twelve and the phase margin of the filter depends on the amplifier's own output impedance.

Buffering is the other common use. Four channels of a reference divider, four sensor outputs, four cable drivers. The output sources well enough for a light load and sinks poorly, so a cable with a 50 ohm termination is a heater rather than a load, and the current limit of 40 to 60 milliamps is what protects the part.

The thermal coupling inside a quad body

Four amplifiers on one die share a junction. When one channel drives a heavy load the local temperature rises and the other three see an offset shift, which is the reason a quad package is a poor choice for four independent precision channels and a good choice for four related ones.

The magnitude is modest at this quiescent current and large at fault current. A channel shorted to ground draws 40 milliamps, dissipates 60 milliwatts in the output stage, and raises the junction by several degrees in a small outline body. Over a minute that is a few millivolts of drift on the neighbours, which is visible on a 12 bit converter and invisible on a comparator.

Questions that come with this code

Is the input really ground sensing? The common mode range includes ground at room temperature and stops 1.5 volts below the positive rail, so a low side current sense works and a high side sense near the rail does not.

Can the output reach ground? It swings to within a few millivolts of ground on a light load, which is what makes a single supply amplifier chain possible, and it does not reach the positive rail.

Is this the same part as LM324A in a tube? Yes, the carrier is the only difference and the electrical table is the same.

Will a B version drop in? Electrically and mechanically yes, and the B release notes should be read for the minimum supply of 3 volts.