Contact Us

LM319MX-NOPB

Brand: Texas Instruments
Texas Instruments LM319MX-NOPB is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM319MX-NOPB — Power Management & Signal Chain | Superb Automation

LM319MX-NOPB

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM319MX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM319MX-NOPB: the plain dual high speed comparator, 80 nanoseconds at 8 millivolts

LM319MX-NOPB is the plain grade of the dual high speed comparator in the fourteen pin small outline body, on a 2500 piece reel, from 0 to plus 70 degrees. The speed is the same as the A sort at 80 nanoseconds typical, and the difference is the input stage: 2 millivolts typical and 8 millivolts maximum of offset at room, against 0.5 and 1 on the A grade.

That trade is the whole decision. When a pulse chain has a volt of signal and a threshold that only has to be roughly right, the plain grade is the correct part and the A sort is wasted money. When the threshold sits on a hundred millivolt pulse, the 8 millivolt maximum is 8 percent of the signal and the A sort stops being optional.

What the string declares

LM is the family, 319 is the commercial window of the dual high speed comparator, M is the small outline body in the vendor's own convention for this family, X is the reel, and NOPB is the lead free declaration. The same body and die is published under LM319AMX/NOPB with the A grade input stage.

Orderable codeLM319MX-NOPB
Comparators per body2, independent
BodySOIC, 14 pins
Carrierlarge tape and reel, 2500 pieces
Part markingLM319M
Temperature window0 to plus 70 degrees
Offset at 25 degrees2 millivolts typical, 8 maximum
Offset over the window10 millivolts maximum
Input offset current80 nanoamps typical, 200 maximum
Input bias current250 nanoamps typical, 1000 maximum
Response time with 5 millivolts of overdrive80 nanoseconds typical
Voltage gain8 volts per millivolt minimum, 40 typical
Output saturation at 25 milliamps0.75 volts typical, 1.5 maximum
Positive supply current4.3 milliamps typical, 12.5 maximum
Maximum ground to supply voltage16 volts

The gain row and what it does to a 5 millivolt overdrive

The voltage gain on the plain grade is 8 volts per millivolt minimum and 40 typical, against 20 and 40 on the A sort. That row is not abstract. The response time is specified with a 5 millivolt overdrive and a 100 millivolt input step, so the comparator has to resolve a small differential into a full output swing within 80 nanoseconds. A part with 8 volts per millivolt of gain turns 5 millivolts into 40 volts of open loop output, which is a full swing on a 15 volt rail, and there is just enough left over.

At 1 millivolt of overdrive the arithmetic stops working. The open loop gain delivers 8 volts, the output is not fully switched, and the delay stretches well past the specified figure. That is why a fast comparator is specified with an overdrive condition and why a circuit that relies on the 80 nanosecond row has to guarantee at least 5 millivolts of overdrive at the input.

The offset row sets how much of the signal is left to be the overdrive. On a 100 millivolt pulse, an 8 millivolt offset consumes 8 percent of the margin, which is acceptable. On a 20 millivolt pulse it consumes 40 percent, and the delay becomes a lottery across parts and temperature.

Split rails, input range and the 16 volt ceiling

The device is specified on plus or minus 15 volts, with an input range of plus or minus 13 volts and a hard limit of 16 volts from ground to either supply pin. Two volts of headroom at each input is the price of the wide common mode range, and it is why the part is usually fed from plus or minus 12 or plus or minus 15 rather than from whatever rail is on the board.

The negative supply current is 3 milliamps typical and 5 maximum, so a board that generates the negative rail from a charge pump has to budget 5 milliamps for one package and 10 for two. That is a real constraint in a battery instrument, and it is the point where a 1.3 microsecond comparator on a single 5 volt rail starts to look better than an 80 nanosecond part with a charge pump.

The output can sit on a rail above the positive supply of the following stage, up to 35 volts, and the leakage at that voltage is 10 microamps maximum. On a 1 kilo ohm pull up that is 10 millivolts, and on 100 kilo ohms it is a volt, so the pull up has to be sized against the leakage and not only against the edge rate.

Sourcing the plain grade

The plain grade is the volume code in this family and the one most likely to be in stock at several distributors. That makes it a reasonable default for a new build, with the A sort reserved for the channels that actually need the tighter input stage.

Our amplifier cross reference page keeps the notes on the wider analogue family that shares this pinout and function, and the obsolete part cross reference hub covers what happens when a lead free declaration changes and the string with NOPB is replaced by a plain string on the same body.

One practical point on incoming inspection. The part marking on this body is LM319M, and the A grade carries LM319AM, so a reel labelled with the full order string and a body marked LM319M is correct and not a substitution. That mismatch between label and marking is the most common false alarm on this family.

How a pulse chain ends up with the plain sort

A pulse chain usually starts with a sensor that delivers volts and ends with a gate that needs a clean edge. Somewhere in the middle a threshold has to be crossed, and if the pulse is short the comparator becomes the speed limit for the whole chain. That is the point at which the plain grade of this part enters, because it delivers 80 nanoseconds at a price the A sort cannot match.

The tolerance comes from the pulse height. A 2 volt pulse against an 8 millivolt offset window has 250 times the margin it needs, and the plain sort is exactly right. A 50 millivolt pulse against the same window has six times the margin at room and less over temperature, and that is where the A sort or a different circuit belongs.

Substitution notes for this family

The body is fourteen pins and the pinout is not the quad comparator pinout, so a substitution has to be checked pin by pin rather than by body size. The supply pins are the ones that differ first, and the second difference is the output arrangement, which brings both the collector and the emitter out.

Two grades in one body also means two part markings, LM319M and LM319AM, and a line that receives both grades has to read the marking rather than the reel label. That single check catches the most expensive substitution error in this family, which is an A grade part approved for a channel that is then filled from the plain grade reel.

Speed is also worth measuring rather than trusting. A bench that sees 200 nanoseconds instead of 80 is usually looking at a pull up that is too large, a load capacitance above the 15 picofarads used for the specification, or an overdrive below the 5 millivolts that the row assumes. All three are cheaper to fix than a faster comparator.

Questions that come with this code

Is the speed different from the A grade? No, both are 80 nanoseconds typical with 5 millivolts of overdrive, and the difference is offset, offset current, bias current and gain.

Can it run on a single 12 volt rail? Yes, within the 16 volt ground to supply limit, though the input range is then 2 volts below the rail rather than plus or minus 13.

What is NOPB? The lead free declaration used by the original vendor of this family, kept in the string when the catalogue page was carried across.

Is the part still active? The addendum prints the reel rows for both grades as active production on the eight hundred and fifty piece and twenty five hundred piece carriers, and the reel on this string is the twenty five hundred.