LM317LMX-NOPB
Product Specifications
LM317LMX-NOPB
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM317LMX-NOPB from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM317LMX-NOPB: the 100 mA regulator in the SOIC body
LM317LMX-NOPB is a low current member of the LM317 family, the 100 mA device in an eight pin small outline body on tape, with the NOPB suffix marking the lead free ordering form. The electrical behaviour is the same as the larger parts in the family, a floating three terminal regulator that holds the differential between input and output at 1.25 V to 37 V with two resistors, but the current class is one fifteenth of the 1.5 A device and the packages are built for control boards rather than for power stages.
SLCS144G, revised August 2026, is the document behind this string. It carries a useful split that older revisions did not: the table separates the legacy chip from the new chip, and the two do not share their regulation rows. A buyer who treats every LM317L as identical across a decade of stock is comparing parts from two different fabrication generations without knowing it.
What follows is the electrical split between the two chips, the carrier table for the four bodies, the reason the SOIC body needs a note on its unused pins, and the questions that come with a legacy suffix on a part that is still active.
The rows that separate the two chips
Input regulation is the clearest difference. The new chip is printed at 0.007 percent per volt typical and 0.021 maximum at 25 degrees, the legacy chip at 0.01 and 0.02. Over the full window the new chip holds 0.006 to 0.0275 while the legacy part moves to 0.02 and 0.05. For a 30 V input change that is the difference between 2 millivolts and 15 millivolts of output movement on a 5 V rail.
| Output current class | 100 mA |
| Output voltage window | 1.25 V to 37 V, set by two resistors |
| Reference voltage | 1.2 V minimum, 1.25 V typical, 1.3 V maximum |
| Input regulation, new chip, 25 degrees | 0.007 percent per volt typical, 0.021 maximum |
| Input regulation, legacy chip, 25 degrees | 0.01 percent per volt typical, 0.02 maximum |
| Input regulation, new chip, over temperature | 0.006 percent per volt typical, 0.0275 maximum |
| Output regulation at 25 degrees | 25 millivolts, VO at or below 5 V, IO 2.5 mA to 100 mA |
| Ripple rejection at 120 Hz | 71.5 dB typical new chip, 80 dB typical legacy, with 10 microfarads on the adjustment pin |
| Minimum output current to hold regulation | 1.5 milliamps typical, 2.5 maximum on the new chip |
| Adjustment pin current | 50 microamps typical, 100 maximum |
| Change in adjustment pin current | 0.2 microamps typical, 5 maximum |
| Output voltage change with temperature | 10 millivolts over 0 to 125 degrees on the legacy chip |
| Output noise, 10 Hz to 10 kHz | 3 microvolts per volt of output, 10 maximum on the new chip |
| Long term drift, 1000 hours at 125 degrees | 10 microvolts per volt of output |
Four bodies and their carriers
The SOIC body is the one this page is about, and the addendum prints it in both a C grade and an I grade. The C grade runs from 0 to 125 degrees, the I grade from minus 40 to 125 degrees, and both use the same eight pin outline at 4.9 mm by 6 mm. Tape quantities are 75 pieces in a tube and 2500 pieces on a large reel, which is a standard feeder width and the reason the body is popular on mixed technology boards.
| LM317LCD | SOIC, 8 pins, 75 pieces per tube, moisture level 1, 0 to 125 degrees |
| LM317LCDR | SOIC, 8 pins, 2500 pieces on a large reel, moisture level 1 |
| LM317LID | SOIC, 8 pins, 75 pieces per tube, minus 40 to 125 degrees |
| LM317LIDR | SOIC, 8 pins, 2500 pieces on a large reel, minus 40 to 125 degrees |
| LM317LCLP | TO-92, 3 pins, 1000 pieces bulk, 0 to 125 degrees |
| LM317LCLPR | TO-92, 3 pins, 2000 pieces on a large reel, 0 to 125 degrees |
| LM317LCPK | SOT-89, 3 pins, 1000 pieces on a large reel, 0 to 125 degrees |
| LM317LCPW | TSSOP, 8 pins, 150 pieces per tube, moisture level 2 |
| LM317LCPWR | TSSOP, 8 pins, 2000 pieces on a large reel, moisture level 1 |
| Part marking, SOIC C grade | L317LC |
| Part marking, SOIC I grade | L317LI |
| Moisture rating, SOIC rows | level 1, unlimited floor life at 260 degrees |
| Lead finish | nickel palladium gold on the SOIC rows |
The LMX suffix is the legacy ordering form for the small outline body on tape, and the NOPB suffix is the lead free marker that older catalogues carried instead of a separate RoHS column. Neither suffix appears in the current addendum, which prints LM317LCDR and LM317LIDR for that body. The honest reading is that the string describes the same body under an older naming convention, and that a buyer should confirm the carrier and the date code against the vendor's live list before a production release. We do not treat a legacy suffix as evidence of a different die.
The unused pins in the eight pin body
The SOIC and TSSOP bodies carry eight pins for a three terminal function, so five pins are not connected. The data sheet figures show the recommended treatment, which is to tie the unused pins to ground on the SOIC body rather than leave them floating. That matters in an environment with fast edges nearby, because a floating pin inside the package acts as a small antenna and the coupling lands on the adjustment node, which is the highest impedance point in the circuit.
The other consequence of the eight pin body is thermal. The die is small and the package has no tab, so the dissipation ceiling is set by the lead frame and the copper under the pins. At 100 mA and a 10 V differential the device dissipates 1 W, which is more than the body can hold at 125 degrees ambient without a plane, so the practical ceiling for a continuous load at high differential is around 400 milliwatts.
Where the 100 mA part is the right choice
Control boards are the natural home. A 24 V loop supply that has to produce 12 V at 20 mA for a relay driver and an op amp rail is a 240 milliwatt dissipation, well inside the body, and the part needs no output capacitor to stay stable, which removes one component from a board that is already tight. The floating topology also lets the regulator sit above a shunt in a current loop without a separate isolated supply, which is the second common use.
The third use is a post regulator. A switching stage that produces 8 V with 40 millivolts of ripple, followed by this device at 5 V, gives ripple rejection of 71.5 dB at 120 Hz on the new chip, which puts the residue under a millivolt. The power management cross reference page lists the pin compatible bodies for the eight pin outline, and the lead time page covers what we do when the C grade is quoted at eight weeks and the I grade is on the shelf.
Questions that come with a legacy suffix
Is the new chip a drop in for the legacy chip? Electrically yes, the pinout and the reference are the same and the new chip is tighter on input regulation. The difference that catches people is the minimum output current, which is printed at 1.5 milliamps typical on the new chip, so a circuit that relied on a 5 milliamp bleeder still works and a circuit that removed the bleeder may not.
Does the NOPB suffix change the moisture rating? No. The SOIC rows are level 1 at 260 degrees in both the plain and the suffixed forms, which means no bake is required at any point in the floor life.
Which body should be used for a new board? The SOIC body if the board is machine placed, the SOT-89 if the dissipation is at the top of the range, because the tab carries heat into the plane, and the TO-92 only where a through hole part is still required. The incoming inspection plan sets out the checks we run on each carrier type before a lot is released to the line.
What is the failure mode at overload? The device reduces output current or shuts the output stage down, and restarts when the overload is removed. Repeated cycling into thermal shutdown is printed in the data sheet as a hit on long term reliability, which is why a rail that is expected to survive a continuous short should be fused rather than protected by the regulator alone.