LM311DR
Product Specifications
LM311DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The LM311DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
LM311DR: the same comparator on a 2500 piece reel for a running line
LM311DR is the commercial grade single strobed comparator in the eight pin small outline body, on a 2500 piece reel, guaranteed from 0 to plus 70 degrees. It is the production twin of the tube body: same die, same pinout, same electrical table, and a carrier that a placement machine can actually use.
The reason to treat the reel as its own part rather than as a packaging detail is that production problems cluster around carriers. A reel that arrives with the wrong tape width, a pocket that is too shallow for the body, a moisture level that needs a bake, or a partial reel carried across a build all cost line time in a way that a tube never does.
The string, the grade and the carrier
LM is the family prefix, 311 is the commercial grade input stage, D is the eight pin small outline body, and R is the tape and reel carrier. The electrical rows are the ones the whole family shares: 0.7 millivolts typical offset, 100 nanoamps maximum bias current, 115 and 165 nanosecond response times, and a 50 volt 50 milliamp open collector output.
The temperature window is the one the grade prints. The commercial grade is guaranteed from 0 to plus 70 degrees, which covers every sealed instrument enclosure that is not mounted next to a heat source. When the board does sit next to a heat source, the LM211 with the same pinout covers minus 40 to plus 85, and the LM211Q covers minus 40 to plus 125, both of which are drop in on the eight pin body.
| Orderable code | LM311DR |
| Channels | 1, differential input, strobed |
| Body | SOIC, 8 pins, 4.9 by 3.9 millimetres nominal |
| Carrier | tape and reel, 2500 pieces, 330 millimetre reel, 12.4 millimetre tape |
| Temperature window | 0 to plus 70 degrees |
| Lead finish | nickel palladium gold, level 1 moisture rating at 260 degrees |
| Part marking | LM311 |
| Response time | 115 nanoseconds low to high, 165 high to low |
Reading the offset and bias rows on a production budget
Offset voltage is 0.7 millivolts typical and 3 millivolts maximum at 25 degrees, widening to 4 millivolts over the range. On a running line the maximum is the number that matters, because a threshold that is trimmed against the typical value produces a yield curve that drifts with the lot.
Bias current is 75 nanoamps typical and 100 maximum, offset current 4 nanoamps typical and 10 maximum. The bias current is the row that decides the divider impedance, and on a board that already carries a 100 kilo ohm divider the drop is 10 millivolts, which is larger than the offset window. The cheap fix is to halve both resistors, which doubles the standing current, and the correct fix is to balance the source impedance on both inputs so that the bias currents cancel.
| Input offset voltage at 25 degrees | 0.7 millivolts typical, 3 maximum |
| Input offset voltage over the range | 4 millivolts maximum |
| Input bias current | 75 nanoamps typical, 100 maximum |
| Input offset current | 4 nanoamps typical, 10 maximum |
| Common mode range on plus or minus 15 volts | minus 14.5 to plus 13 volts |
| Large signal gain | 40 volts per millivolt minimum |
| Saturation voltage at 50 milliamps | 0.75 volts typical, 1.5 maximum |
| Output leakage over temperature | 0.5 microamps maximum |
Carrier details that decide whether the line stops
The reel is 330 millimetres with 12.4 millimetre tape, a 6.4 by 5.2 millimetre pocket 2.1 millimetres deep, and 2500 pieces. The pocket depth matters for an eight pin small outline body because a shallow pocket lets the body ride up in the tape and the nozzle picks it at an angle, which shows up later as a tombstone on a two terminal part and as a lifted lead on this one.
Tape width is the other number the line checks. A 12.4 millimetre carrier is the standard for this body size and it fits the feeders that most placement machines already have loaded, so a reel that arrives on an 8 millimetre carrier stops the line while someone finds an adapter. That is the kind of detail a purchase order should carry, and it is the reason the carrier is written on the drawing rather than left to the supplier.
The moisture rating is level 1 at 260 degrees, so no bake is needed before the feeder. That is the practical advantage of the nickel palladium gold finish over a tin finish at level 2 or 3, and it is the difference between a reel that can go straight onto the machine and one that has to sit in an oven overnight. A partial reel is not returnable, so a line that runs 200 pieces a week should plan the reel across two builds and record the date code once.
Where the part sits in a signal chain
The comparator is usually the last analogue stage before a digital input, and its job is to turn a slow, noisy signal into one clean edge. The two parameters that decide how well it does that are the offset and the response time, and the third is the hysteresis, which the part does not include and the board has to add.
The usual hysteresis network is a resistor from the output back to the non inverting input, which turns the threshold into two thresholds. With an open collector output the feedback has to come from the collector node, after the pull up, otherwise the network sees the transistor rather than the logic level. A 1 megaohm feedback resistor against a 10 kilo ohm divider gives about 1 percent of hysteresis, which is enough to stop chatter on a 100 millivolt signal and small enough not to shift the threshold.
The response time rows are worth reading twice. The 115 and 165 nanosecond figures are quoted for a 100 millivolt step with 5 millivolts of overdrive, and overdrive is the parameter that sets the delay in practice. A signal that crosses the threshold slowly, at 1 millivolt per microsecond, spends 5 microseconds inside the overdrive band and the output follows that slope rather than the datasheet figure. A signal with a fast edge gets the quoted number. That is why a comparator behind a slow thermistor is chosen for its offset and a comparator behind a fast pulse is chosen for its response time, and a part that is good at one is not automatically good at the other.
The reel, the kit and the audit trail
A 2500 piece reel covers a week at 400 boards a day with one part per board, and it covers four weeks at 100 a day. The kitting step records the reel, the date code and the quantity, and that record is what a customer audit asks for. Our kitting service page sets out what we record per reel, and the traceability report page shows the report a customer receives when a build ships.
When the reel runs out mid build, the next reel is a different date code even when it is the same part number, and the two reels are recorded as two lots. That is the reason a line prefers to finish a build on one reel: it keeps the traceability record simple and it removes one variable from a field return investigation.
Questions that come with this code
Is the reel body the same as the tube body? Yes, the same die, the same eight pin small outline package, the same finish and the same marking. Only the carrier and the quantity differ.
Can I put 2500 pieces through a line that builds 50 boards a week? Yes, and the reel should be stored in a dry cabinet between builds, with the date code recorded at the first use rather than at receipt.
What if the line needs the wider temperature window halfway through the programme? The LM211 and the LM211Q are drop in on the same footprint, and our drop in replacement verification page lists the two rows, the offset and the bias current, that have to be re-checked before the substitution is signed off.