Contact Us

LM293AD

Brand: Texas Instruments
Texas Instruments LM293AD is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM293AD — Power Management & Signal Chain | Superb Automation

LM293AD

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM293AD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM293AD: the A grade dual comparator in a tube, two millivolts at room

LM293AD is the A grade of the dual differential comparator in the eight pin small outline body, supplied in a tube, guaranteed from minus 25 to plus 85 degrees. The family it belongs to is the one that most threshold circuits on a board still come from, and the A sort is the version to buy when the threshold has to hold without a trim.

Two comparators in eight pins, a supply range from 2 to 36 volts, an input range that includes ground, and an open collector output that can be tied to another output. Those are the properties that put this part in a window detector, a zero crossing monitor, a current limit and a supply sequencer without any of them needing an extra device.

The tube matters for the kind of buyer this page is written for. A prototype shop, a repair centre and an instrument builder buy a few hundred a year, and a tube can be split across builds while a reel cannot be split without creating a second record.

What the A grade buys

The plain LM293 holds 2 millivolts typical and 5 millivolts maximum at 25 degrees, widening to 9 millivolts over the window. The A sort holds 2 millivolts maximum at 25 degrees and 4 millivolts over the window, which is a little over half the spread at the extremes and a factor of two and a half at room.

That difference decides two things. On a window detector built from both comparators in the package, the two thresholds drift independently, so the window can close or open by the sum of the two offsets. On a threshold that is set by a divider from the same rail as the signal, the offset is a fixed percentage of full scale and the A sort halves the untrimmed error.

Orderable codeLM293AD
Comparators per body2, independent
BodySOIC, 8 pins
Carriertube
Temperature windowminus 25 to plus 85 degrees
Offset at 25 degrees1 millivolt typical, 2 maximum
Offset over the window4 millivolts maximum
Input bias current at 25 degrees25 nanoamps typical, 250 maximum
Input bias current over the window400 nanoamps maximum
Common mode range at 25 degreesground to 1.5 volts below the positive rail
Large signal gain50 volts per millivolt minimum, 200 typical
Output low voltage at 4 milliamps110 millivolts typical, 400 maximum
Output sink current at 1.5 volts6 milliamps minimum
Supply current, both comparators0.6 milliamps typical at 5 volts
Response time with 5 millivolts of overdrive1.3 microseconds typical

The input range is the row that keeps the circuit simple

The common mode range runs from ground to 1.5 volts below the positive rail at room temperature, and to 2 volts below it over the window. Ground is included, which means a comparator can watch a low side shunt, a single cell or a signal that swings below the negative rail of the next stage, without a negative supply.

The upper end is the constraint that catches people. On a 5 volt rail the input stops at 3.5 volts, so a threshold set at 4.2 volts cannot be compared directly. The usual fix is a divider, which buys back the range at the cost of source impedance, and source impedance then multiplies the 250 nanoamp bias current into an error that can exceed the offset window.

The document adds one more row that matters and is easy to miss. Either input can go up to the full supply level without damage, and the output stays correct as long as the other input is inside the common mode range. That allows a circuit where one input sits on the rail and the other does the work, which is exactly the arrangement a supply sequencer needs.

The output, the pull up and the wired AND

The output is an open collector transistor. It sinks 16 milliamps typical at 1.5 volts and drops 110 millivolts at 4 milliamps, rising to 400 millivolts maximum at room and 700 over the window. The low level is what a logic gate sees, so a 400 millivolt worst case is inside the 0.3 times supply limit of a 5 volt CMOS input but outside it at 3.3 volts, where 0.99 volts is the limit and the margin is still comfortable.

Two open collectors tied to one pull up make a wired AND, which is the cheapest way to combine two fault conditions into one signal. The pull up value trades speed against current. At 4.7 kilo ohms on 5 volts the sink current is about 1 milliamp and the rise time into 50 picofarads is a few microseconds; at 1 kilo ohm the current is 5 milliamps and the edge is sharper, at 25 milliwatts per comparator that is low.

Leakage when the output is off is 50 nanoamps typical and 1 microamp maximum over the window, so a 100 kilo ohm pull up can sit 100 millivolts above ground at the hot end. On a threshold that reads the node with a second comparator, that is a real offset and not a rounding error.

Why a tube rather than a cut tape

A tube holds the parts in a channel with the leads exposed and can be split across builds without losing the carrier. For a bench that builds twenty boards, changes a resistor, builds twenty more, that is the right unit. It also stacks and stores without a reel stand, which matters in a small lab.

The handling procedure is the same as any small outline part: level 1 moisture rating means no bake, and the finish is nickel palladium gold on the current rows, so a shelf life measured in years is normal as long as the tube is not stored open in a humid room.

When the volume grows past a few thousand a year, the reel string is the one to move to, and the electrical table does not change. Our pin to pin cross reference page covers the family substitutions that keep the same footprint, and the amplifier cross reference page is where we keep the notes on the wider group of analogue parts that share this pinout pattern.

There is one sourcing point specific to this family. Because several vendors build the same eight pin dual comparator, the cheapest active code is not always the one on the approved list, and the difference between an A sort and a plain sort from a second vendor can be larger than the difference between two vendors of the same sort. Comparing sort to sort is the only comparison that means anything.

Tube counts and the bench that mixes sorts

A bench that buys both the plain grade and the A sort keeps two tubes that look identical from the outside. The part marking on this family does not carry the sort letter on every vendor's body, so the tube label is the only reliable evidence, and a tube that loses its label becomes a mixed tube after the first rebuild.

The practical rule is one tube per sort per drawer, with the label facing up and the date code written on the tube end. A tube that has been opened, emptied half way and refilled from a second tube should be relabelled with the older date code, since that is the code a customer audit will look for.

Tube handling also sets a limit on how many times a part can be presented to a hand feeder. Nickel palladium gold is a hard finish and survives repeated handling better than tin, but a lead that has been bent straight twice is no longer a lead, and a tube is where that damage happens.

Questions that come with this code

Does the tube change the moisture rating? No. The rating belongs to the body and the finish, and it is level 1 at 260 degrees on the current rows.

Can this part run from a single 3.3 volt rail? Yes, the supply range starts at 2 volts, and the input range still includes ground, so a divider from the 3.3 volt rail works without a negative supply.

What happens if an input goes below ground? The document allows 0.3 volts below the negative rail before the output can be wrong and excessive input current can flow, so a signal that rings below ground needs a clamp.

Is the response time fast enough for a current limit loop? At 1.3 microseconds typical the comparator is faster than most switching supplies need, and the limit is usually the gate driver rather than the comparator.