Contact Us

LM285MX-1.2

Brand: Texas Instruments
Texas Instruments LM285MX-1.2 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM285MX-1.2 — Power Management & Signal Chain | Superb Automation

LM285MX-1.2

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM285MX-1.2 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM285MX-1.2: the micropower 1.2 volt reference on a small outline reel

LM285MX-1.2 is the two terminal band gap voltage reference that holds 1.235 volts, in the eight pin small outline body, on tape and reel, guaranteed from minus 40 to plus 85 degrees. It is the reference an engineer reaches for when the board has a microcontroller in sleep mode and the reference cannot be allowed to draw milliamps while the rest of the system is off.

The device is a shunt reference, not a series regulator: it needs a current sourced into its cathode and it holds the voltage across itself. That single sentence explains most of the mistakes made with it, from a board that expects a stable output with no bias resistor to a board that runs the reference at 20 milliamps and wonders why the package is hot.

What the string declares and what it does not

LM is the family prefix, 285 is the micropower grade, the suffix after the dash is the reference voltage, M is the small outline body, and X is the reel carrier. The 1.2 in the string is the voltage family, whose actual value is 1.235 volts rather than 1.2, which matters when a divider is calculated from the rounded name.

The current revision of the document deleted the ordering table, so the reel quantity and the moisture level are not printed in this revision at all. What is printed is the package table, which lists four bodies with their thermal resistance, and the electrical table, which is what a threshold budget is built from. A purchaser who needs the carrier quantity should ask for the packaging addendum of the release in force rather than assume the number from a sister part.

Orderable codeLM285MX-1.2
Reference voltage at 25 degrees1.235 volts nominal, 1.223 to 1.247 volts
Bodies listed in the package tableD eight pins, PS eight pins, PW eight pins, LP three pins
Junction to ambient, D body97 degrees per watt
Junction to ambient, PS body95 degrees per watt
Junction to ambient, PW body149 degrees per watt
Temperature windowminus 40 to plus 85 degrees
Family documentSLVS075J, first issued April 1989, revised January 2015

The operating current window is the whole specification

The reference current runs from 10 microamps to 20 milliamps, and the minimum is the number that decides whether the circuit works at all. Below 10 microamps the reference has not started, and the voltage across it is whatever the rest of the circuit imposes, which in a comparator threshold chain looks like a random trip point rather than a failed part.

At the top of the window the dissipation becomes the limit. Twenty milliamps into 1.235 volts is 24.7 milliwatts, which in the small outline body at 97 degrees per watt is 2.4 degrees of rise, and in the three pin body at 140 degrees per watt it is 3.5 degrees. Neither is dangerous on its own, and both become relevant when the reference sits inside a sealed enclosure at 70 degrees ambient with a bias resistor sized for a 15 volt rail.

Reference current range10 microamps to 20 milliamps
Reference voltage at 25 degrees1.223 to 1.247 volts, 1.235 nominal
Average temperature coefficientplus or minus 20 parts per million per degree
Reverse current, absolute maximum30 milliamps
Forward current, absolute maximum10 milliamps
Operating junction temperature150 degrees, absolute maximum
ESD, human body modelplus or minus 2000 volts
ESD, charged device modelplus or minus 1000 volts

Sizing the bias resistor, and why the tolerance is not where people look

The resistor from the supply to the cathode has to pass at least 10 microamps at the lowest supply and no more than 20 milliamps at the highest, and it has to do that while the load takes its own current. On a 3.3 volt rail with a 1.2 volt reference and a light load, 22 kilo ohms passes about 95 microamps, which is comfortable. On a 24 volt rail the same resistor passes 1 milliamp, which is still inside the window and costs 24 milliwatts in the resistor.

The tolerance that surprises people is not the initial 1 percent, it is the combination of the temperature coefficient and the operating current. Twenty parts per million per degree over the 125 degree window of the family is 2.5 millivolts, which is twice the initial error, so a circuit that trims at room temperature has to budget the drift separately. Our incoming inspection plan page covers how we check a reference lot before it reaches a build, since a reference that is inside tolerance at 25 degrees can be outside it on the board.

A worked example makes the budget concrete. A 12 bit converter with a 1.235 volt reference has a least significant bit of 302 microvolts, so the 12 millivolt window of the reference grade is 40 counts before anything else is considered, and the 2.5 millivolts of drift over the window is 8 counts. That is why a 12 bit instrument usually trims the reference against a calibrated meter at final test rather than relying on the grade alone, and why the grade matters more in a 10 bit converter where the counts are four times larger.

Where a shunt reference is the right answer and where it is not

A shunt reference is the right answer when the load is light, the supply is well above the reference, and the board needs the reference to keep working while the rest of the system sleeps. It is the wrong answer when the supply is close to the reference voltage, because the bias resistor then has almost no headroom and the current collapses at low line, and it is the wrong answer when the load is heavy, because every milliamp of load has to be added to the bias current.

In a comparator threshold chain the reference usually feeds a divider, so the load is tens of microamps and the shunt is comfortable. In an analogue to digital converter reference input the load is a switched capacitor that draws bursts of current, and the shunt needs a capacitor close to the pin plus a bias current several times the average load. Both cases appear in the same instrument, which is why the reference and its bias resistor belong on the same page of the circuit review.

The body, the reel and the handling

The small outline body is the one most boards use, and the three pin body is the one that survives a through hole prototype. The thermal numbers differ by more than 40 percent between them, which matters only at the top of the current window, and the pinout differs enough that a board cannot be laid out for both.

The reel carrier is the production choice, and the current revision does not print its quantity, so the number should be taken from the packaging addendum rather than from a sister device. What the revision does print is the moisture behaviour of the family, which is a level 1 body in the small outline version, meaning no bake before the feeder. Our power management cross reference page lists the reference family equivalents and their initial tolerances, and the traceability report page shows how a reference reel is recorded against a build.

Questions that come with this part

Is 1.2 volt the actual reference value? No, it is 1.235 volts nominal, with a window of 1.223 to 1.247 volts at 25 degrees. A divider calculated from 1.2 volts is 3 percent low, which is larger than the grade of the reference.

Can it be used as a 1.235 volt regulator? Only as a shunt, with a series resistor and a load that never drops below the minimum current. For anything that needs to source current into a load, a series reference is the correct part.

What happens at 20 milliamps? The reference still holds, and the package temperature rises by the thermal resistance times the dissipation. The 30 milliamp absolute maximum is the hard limit, not an operating point, and our last time buy page covers the case where a board has to keep an older reference grade alive past its withdrawal date.