Contact Us

LM139AD

Brand: Texas Instruments
Texas Instruments LM139AD is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

LM139AD — Power Management & Signal Chain | Superb Automation

LM139AD

Texas Instruments — Power Management & Signal Chain

Product Overview

The LM139AD from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

LM139AD: the tight offset A grade of the quad comparator, and the code the vendor has stopped building

LM139AD is the A grade of the quad voltage comparator in the fourteen pin SOIC, specified over minus 55 to plus 125 degrees with 2 millivolts maximum of offset at 25 degrees and 4 millivolts over the full range. The four comparators share one bias block and each has an open collector output that can sink 16 milliamps.

The vendor addendum prints this code as obsolete, with the reel code LM139ADRG4 still active. That is the practical fact of this page: a board that specifies the tube or bulk code has to move to the reel code to keep buying the same die, and the move is a carrier change rather than a part change.

LM139AD as the vendor document publishes it

Channels4
Supply2 to 36 volts single, or split supplies
Supply current0.8 milliamps typical, 2 milliamps maximum for four comparators
Offset voltage, A grade1 millivolt typical, 2 millivolts maximum at 25 degrees
Offset voltage, A grade over temperature4 millivolts maximum
Offset voltage, plain code2 millivolts typical, 5 millivolts maximum at 25 degrees
Offset voltage, plain code over temperature9 millivolts maximum
Input bias current3.5 nanoamps typical, 25 nanoamps maximum at 25 degrees
Input offset currentplus or minus 5 nanoamps typical, plus or minus 25 maximum
Common mode input rangezero to the positive supply minus 1.5 volts
Input toleranceeither input to 30 volts without damage
Response time1.3 microseconds with 5 millivolts of overdrive
Output sink current16 milliamps at 1.5 volts of low level
Low level output150 to 400 millivolts at 4 milliamps
Output typeopen collector
Temperature rangeminus 55 to plus 125 degrees
Package14 pins, SOIC body D
Catalogue codeLM139AD
Vendor statusobsolete at the vendor
Replacement pathLM139ADRG4, same die on the reel
Package14 pins, SOIC body D
Temperature rangeminus 55 to plus 125 degrees

Two millivolts on the A grade, five on the plain code

The input offset voltage of the A grade of LM139AD is 1 millivolt typical and 2 millivolts maximum at 25 degrees, with 4 millivolts maximum over the full temperature range. The plain code is 2 millivolts typical and 5 millivolts maximum at 25 degrees, with 9 millivolts maximum over the range.

That factor of two is the whole difference between the two codes, and it matters in a threshold detector where the trip point is set by a divider: 5 millivolts of offset on a 100 millivolt threshold is 5 per cent of the set point before any divider tolerance is counted. The A grade is the one to buy when the threshold is tight and the plain code when it is not.

Four comparators from two volts to thirty six

LM139AD is a quad voltage comparator that runs from a single supply of 2 to 36 volts or from split supplies, with the four comparators sharing one bias block and one ground pin. Each comparator has an open collector output, so the four can be wired together into a single line without external logic.

The inputs can go to 30 volts without damage and one input may sit above the positive supply while the other stays inside the common mode range, which is what allows the part to monitor a high side signal from a low voltage rail. The temperature range is minus 55 to plus 125 degrees on the military grade code and narrower on the commercial ones.

Common mode to the positive rail minus one and a half volts

The common mode input range of LM139AD is zero to the positive supply minus 1.5 volts, and either input may go above the positive supply as long as the other one stays inside the range. Neither input may go more than 0.3 volts below ground, which is the constraint that decides whether a negative going signal needs a clamp.

The 1.5 volt gap at the top is why the part cannot be used as a high side current sense comparator on its own supply rail, and why the input above the rail allowance exists: the high side signal is compared against a threshold on the other input rather than against the rail itself. A comparator with a rail to rail input does the same job without that restriction.

One point three microseconds with five millivolts of overdrive

The response time of LM139AD is 1.3 microseconds with a 100 millivolt input step and 5 millivolts of overdrive, measured with the output pulled to 5 volts through 5.1 kilo-ohms. The output sink current is 16 milliamps at 1.5 volts of low level, and the low level output voltage is 150 to 400 millivolts at 4 milliamps.

The overdrive condition is the part of that row most often missed: a comparator that is 1.3 microseconds at 5 millivolts of overdrive takes much longer at 1 millivolt, so a slow moving input near the threshold is the case where the delay grows. That is why a comparator with hysteresis is used on a slow signal rather than a bare one.

Eight hundred microamps for four comparators

The supply current of LM139AD is 0.8 milliamps typical and 2 milliamps maximum for all four comparators, independent of the output state, because the output stage is open collector and draws its current from the pull up resistor rather than from the supply pin. The output can sink 16 milliamps, which is enough for a light emitting diode or a relay driver.

Two milliamps for four comparators is 500 microamps each, which is why the part appears in battery instruments that need four threshold detectors. The open collector output also allows a wired or connection, so four fault flags can share one interrupt line and one pull up resistor without any external logic.

Where a quad comparator belongs

LM139AD belongs in a window detector, a four channel threshold alarm, a zero crossing detector, a pulse width modulation generator, and a battery monitor with four cell taps. In each case the four comparators share a reference divider and one pull up resistor, which is the arrangement the open collector output suits.

The 2 to 36 volt supply range is the row that makes the part useful across a product line: the same code runs on a 5 volt logic rail and on a 24 volt industrial rail with no change to the circuit. What it does not do is compare signals within 1.5 volts of its own positive rail, and that limit, not the speed, is what usually sends a board to a different part.

What the open collector output buys and costs

The open collector output sinks 16 milliamps and sources nothing, which is why four comparators can share one pull up resistor and one interrupt line. The cost is that the rise time is set by the resistor and the track capacitance, so a 100 kilo-ohm pull up on a 20 picofarad line takes 2 microseconds to rise, which is longer than the comparator's own 1.3 microsecond response.

The second cost is the logic level. The output can be pulled to a different supply than the comparator runs on, which is useful when a 24 volt detector talks to a 3.3 volt controller, and it also means the pull up has to be chosen against the input leakage of whatever reads it. A 10 kilo-ohm pull up is the usual compromise and a 1 kilo-ohm one is used when speed matters more than current.

An obsolete order code is a supply question before it is an electrical one. Our last time buy planning page covers the remaining quantity, and the amplifier cross reference page covers the rest of the comparator family.

Is LM139AD the same part as LM139ADRG4? Yes. The G4 suffix marks the lead finish change and the R marks the reel, and the die and the electrical rows are the same.

What is the worst case offset over temperature? 4 millivolts on the A grade and 9 millivolts on the plain code, which is why a tight threshold detector buys the A grade rather than trimming the divider.