ISO7321CDR
Product Specifications
ISO7321CDR
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO7321CDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO7321CDR: dual-channel digital isolator at 25 Mbps with robust EMC in a narrow 8-pin SOIC
ISO7321CDR is a two-channel digital isolator with one channel each way and system level transient immunity in a SOIC body of 8 pins. The 7321 arrangement is one channel each way, and the C suffix is the 25 Mbps grade with a 33 nanosecond typical propagation delay and 65 kV per microsecond transient immunity. It is a narrow body part rated 3000 V RMS, and it is built for boards where the barrier sits next to a switching node rather than in a quiet corner.
Order code and package
| Order code | ISO7321CDR |
| Function | dual-channel digital isolator |
| Package | SOIC, 8 pins, narrow body |
| Channels | two, one forward and one reverse |
| Signaling rate | 25 Mbps |
| Propagation delay | 33 nanoseconds typical at 5 V |
| Transient immunity | 65 kV per microsecond typical at 5 V |
| Supply | 3.3 V or 5 V |
| Isolation | 3000 V RMS for one minute per UL 1577 |
| Barrier life | over 25 years |
| Temperature range | minus 40 to plus 125 C |
| Default output | high on this code, the F suffix version defaults low |
Electrical parameters that decide the application
| Barrier | silicon dioxide |
| Input filter | integrated noise filter on both channels |
| Level translation | 3.3 V and 5 V on each side |
| Emc | system level ESD, EFT and surge immunity, low emissions |
| Supply current | 1.7 milliamps per channel at 1 Mbps on 5 V, 1.2 milliamps on 3.3 V |
| Certifications | UL 1577, CSA notice 5A, IEC 60950-1, IEC 61010-1, CQC GB 4943.1 |
| Output | CMOS push pull |
| Channel count | two in this body |
Points to check before this part goes on a BOM
Sixty five kilovolts per microsecond of transient immunity is the highest in this family line, and it is the figure that decides whether an isolator passes an EFT test inside a cabinet full of contactors. A part rated 50 kV per microsecond is not far behind, but the difference shows up on the compliance report rather than on the bench.
The narrow body rating is 3000 V RMS, which is a functional and basic rating for many industrial rails. It is not the same as the 5000 V RMS wide body parts, and swapping the two for a cost reduction changes the safety margin of the whole product rather than one line of the BOM.
The integrated input filter means a spike shorter than the filter width does not appear at the output. On a gate signal that is the difference between a clean drive and a spurious edge, and it costs one propagation delay of extra latency.
The default output is high on this code and low on the F version. A chip select or a driver enable that must be inactive at power up should be routed to the version whose default state is inactive, since the default state appears at the output before the controller has driven anything.
Where this order code fits
Inverter control cards, isolated gate signal paths and industrial IO boards order this code when the isolator has to survive the emissions of the power stage beside it. Boards comparing it with a neighbouring part start from our Power Management Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.
Questions buyers ask
Does this part suit a mains barrier? It is rated 3000 V RMS in the narrow body, which covers basic insulation on many industrial rails; a reinforced mains barrier needs the wide body parts.
Are both channels filtered? Yes, the input noise filter is on both channels of this body, unlike the higher speed grades which use CMOS thresholds without the filter.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Vendor Consolidation page sets out the checks that keep a substitute from failing on the bench.