Contact Us

ADS1248IPWR

Brand: Texas Instruments
Texas Instruments ADS1248IPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADS1248IPWR — Power Management & Signal Chain | Superb Automation

ADS1248IPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ADS1248IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ADS1248IPWR: 24-bit 2 kSPS converter with four differential inputs and two current sources

ADS1248IPWR is the multi-channel member of the family, used where one board reads several sensors in a TSSOP body of 28 pins. The part puts four differential inputs, a gain stage to 128, a 2.048 V reference with 10 ppm per C maximum drift and two matched current sources behind one multiplexer, and adds sensor burnout detection, thermocouple bias, system monitoring and general purpose digital inputs. Conversions run to 2000 samples per second with single cycle settling at every rate.

Order code and package

Order codeADS1248IPWR
Function8-channel, 2 kSPS, 24-bit converter, four differential pairs
InterfaceSPI
Referenceinternal 2.048 V, 10 ppm per C maximum
Excitationtwo matched current sources plus two current outputs
Digital I/O8 general purpose pins shared with the analogue inputs
Supply2.7 to 5.25 V unipolar or plus and minus 2.5 V bipolar
PackageTSSOP, 28 pins, 7.80 mm by 4.40 mm
Temperature rangeminus 40 to plus 125 C
Noise48 nanovolts RMS at a gain of 128
DatasheetSBAS426 revision H
Sensor supportburnout detection, thermocouple bias, system monitor

Electrical parameters that decide the application

Data rateup to 2000 samples per second with single cycle settling
Mains rejection50 Hz and 60 Hz together at 20 samples per second
Reference drift10 ppm per C maximum, which is 2.56 millivolts over 125 C on 2.048 V
Noise at gain 12848 nanovolts RMS, so a 20 mV sensor signal carries about 0.24 microvolts of noise
Input countfour differential pairs against two on the 20-pin member of the family
Excitation rangeprogrammable, matched pair, used for RTD and thermistor excitation
Calibrationself and system calibration commands, so the offset term can be removed in the part
Digital I/Oeight pins, shared with analogue inputs, which is where a board runs out first
Supplyunipolar 2.7 to 5.25 V, or bipolar plus and minus 2.5 V for signals below ground
Package thermalTSSOP 28 in a 7.80 mm body, so the analogue pins sit close to the digital ones

Points to check before this part goes on a BOM

Ten ppm per C maximum on the internal reference is twice the typical figure of the smaller members of the family, and it is a maximum rather than a typical, so a 125 C span costs 2.56 millivolts of reference error before the amplifier contributes anything.

The eight general purpose pins are shared with analogue inputs. A board that needs four differential channels plus relay drives has already used the pins, so the multiplexer budget has to be counted when the circuit is drawn rather than when the board is finished.

Bipolar supply of plus and minus 2.5 V is what allows a thermocouple or a shunt below ground to be read without a level shift, but the digital side then sits at a different reference and the interface levels have to be checked against the host.

Single cycle settling at every data rate is the feature that makes a scanning front end practical: without it, switching channels costs a discard cycle per channel and a four-channel scan runs at a quarter of the headline rate.

Two matched current sources plus two extra current outputs cover a four-wire RTD and a thermistor at the same time, which is the configuration the part is bought for; using all of them at once moves the excitation current into the supply budget.

Burnout detection pushes a small current into the input to prove the sensor is still connected. On a high impedance sensor that current becomes an offset, so it has to be switched off outside the detection window.

Where this order code fits

Boards with one or two sensors stay on the 16-pin members of this family; the four differential pairs here are for a scanning front end. Boards comparing it with a neighbouring part start from our ADC DAC Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

How many differential channels does this part have? Four, against two on the 20-pin member and one on the 28-pin single-channel member of the same family.

Does it need an external reference? No, the internal 2.048 V reference is specified at 10 ppm per C maximum, but an external reference is still the cheaper way to get better than that.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.