Contact Us

ISO7241MDWR

Brand: Texas Instruments
Texas Instruments ISO7241MDWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO7241MDWR — Power Management & Signal Chain | Superb Automation

ISO7241MDWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO7241MDWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO7241MDWR: the hundred and fifty megabit quad with three channels forward and one back

ISO7241MDWR is the M grade of the four channel digital isolator, three channels from side one to side two and one back, in the sixteen pin wide body SOIC on a large reel of 2000. The M grade runs to 150 megabits per second with a propagation delay of 8 nanoseconds typical, which is the fastest of the family.

The wide body is what gives 8 millimetres of clearance and creepage against the 4 millimetres of the eight pin dual, and that is the reason a mains referenced board uses this part even when two channels would do. The channel to channel skew is 2 nanoseconds, so four lines carrying one word stay aligned to well inside a bit at 25 megabits.

ISO7241MDWR as the vendor document publishes it

Channels4, three forward and one back
Signaling rate25 megabits per second on the C grade, 150 on the M grade
Propagation delay, C grade18 nanoseconds typical
Propagation delay, M grade8 nanoseconds typical
Channel to channel skew2 nanoseconds maximum
Part to part skew8 nanoseconds maximum
Enable and disable delay15 to 25 nanoseconds
Common mode transient immunity25 kilovolts per microsecond minimum, 50 typical
Supply3 to 5.5 volts per side
Withstand isolation2500 volts root mean square for 60 seconds
Maximum repetitive isolation560 volts peak
Maximum transient isolation4000 volts peak
Clearance and creepage8 millimetres
Distance through insulation8 micrometres
Temperature rangeminus 40 to plus 125 degrees
Package16 pins, wide body SOIC DW
Catalogue codeISO7241MDWR
Vendor statusactive
GradeM, 150 megabits per second
Carrierlarge reel of 2000
Moisture levellevel 2, 260 degrees, one year floor life

Three channels one way and one the other

ISO7241MDWR is the quad channel member of the ISO724x family with three channels from side one to side two and one channel back, in a sixteen pin wide body SOIC. The same family publishes a four forward version and a two and two version, so the channel direction is the only difference between three order codes with the same electrical rows.

Each side has an enable pin, and the disabled state is a high impedance output rather than a driven level, which is what allows two isolators to share a bus. The barrier is a silicon dioxide layer, the supply is 3 to 5.5 volts on each side, and the temperature range is minus 40 to plus 125 degrees.

Twenty five megabits on the C grade, a hundred and fifty on the M

The C grade of ISO7241MDWR runs to 25 megabits per second with a propagation delay of 18 nanoseconds typical, and the M grade runs to 150 megabits per second with 8 nanoseconds typical. The input pulse width follows the grade: 25 megabits needs 40 nanoseconds of input pulse, and the M grade needs 6.67 nanoseconds.

The C grade is the one that matches an isolated serial peripheral interface at 20 megahertz, and the M grade is the one that matches a converter interface or a fast digital link where 25 megabits is not enough. Both grades carry the same isolation ratings and the same package, so the speed is a separate decision from the barrier.

Skew between four channels that carry one word

The channel to channel output skew of ISO7241MDWR is 2 nanoseconds maximum, and the part to part skew is 8 nanoseconds maximum, both measured with all inputs driven together and the outputs switching in the same direction. The pulse width distortion is small enough that the family quotes it as part of the skew rather than as a separate row.

Two nanoseconds between four lines matters when the four carry a nibble of one word and the receiver latches on a single clock edge, because the setup and hold window shrinks by that amount. It matters much less when the four channels are four independent signals, which is the more common arrangement on a motor drive.

Twenty five hundred volts in a wide body with eight millimetres

ISO7241MDWR is rated 2500 volts root mean square of withstand for 60 seconds, 560 volts peak of maximum repetitive isolation voltage and 4000 volts peak of maximum transient isolation voltage, with 8 millimetres of external clearance and creepage. The barrier capacitance is about 1 picofarad and the distance through the insulation is 8 micrometres.

The wide body is what buys the 8 millimetres: the eight pin body of the dual channel family gives 4 millimetres for the same barrier. That difference is the reason a mains referenced circuit uses the wide body even when two channels would be enough, because the creepage requirement comes from the standard the product is certified against rather than from the channel count.

Fifteen nanoseconds to disable, twenty five to enable

The enable and disable delays of ISO7241MDWR are 15 to 25 nanoseconds, quoted separately for the high to high impedance and the low to high impedance transitions and for the return paths. Those four rows are what decide whether a channel can be parked between transactions without producing a glitch on the receiving side.

A 25 megabit link with a 20 nanosecond enable delay needs the enable to be asserted at least a bit time before the first edge, which is normally handled by the protocol rather than by the isolator. Where the enable is used to multiplex two isolators onto one bus, the disable delay is the one that sets the dead time between them.

Where four channels belong

ISO7241MDWR belongs on an isolated serial peripheral interface link, where clock, data out, data in and chip select all cross the barrier; on a motor drive, where three pulse width modulated inputs and one fault return cross it; on a data acquisition front end, where four control lines reach an isolated converter; and on a battery management board, where the daisy chain interface and its enable signals cross together.

Three forward and one back is the shape of a serial peripheral interface with a fault line, which is the most common reason to buy this member rather than the four forward version. The reverse channel is also the one that carries the ready signal on a converter interface, so the same part covers both cases.

What the enable pins are for

The enable pins on each side are not a power saving feature. They put the outputs into a high impedance state, which allows two isolators to drive one bus, and they do it in 15 to 25 nanoseconds, which is fast enough to multiplex between two sources within a bit time at 25 megabits.

A board that does not multiplex does not need the pins, and tying them active is the normal arrangement. What the pins must not be used for is a soft start: the high impedance state is a logic state, not a gradual turn on, and a load that needs a ramp needs it on the driver side rather than on the isolator.

The wide body is a creepage decision before it is a channel count decision. Our BOM scrubbing page covers the isolator against the bill of materials, and the incoming inspection plan page covers the barrier check on receipt.

Why buy the quad when two channels are enough? For the 8 millimetres of creepage in the wide body, which the eight pin dual does not offer. The two spare channels are then tied off rather than used.

Does the M grade have the same enable timing? Yes. The enable and disable delays are 15 to 25 nanoseconds on both grades, so the multiplexing behaviour does not change with speed.

What does the barrier capacitance do at this rate? About 1 picofarad across the barrier, which at 25 kilovolts per microsecond of common mode step is 25 milliamps of displacement current. That current has to return through the board, so the two ground planes either side of the isolator are stitched to their own side and not to each other.