Contact Us

ISO1050DUBR

Brand: Texas Instruments
Texas Instruments ISO1050DUBR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ISO1050DUBR — Power Management & Signal Chain | Superb Automation

ISO1050DUBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The ISO1050DUBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

ISO1050DUBR: isolated CAN transceiver with 2500 V RMS isolation in an 8-pin SOIC

ISO1050DUBR is a galvanically isolated CAN transceiver with fail-safe outputs in a SOIC body of 8 pins. The DUB body carries 2500 V RMS isolation for one minute, half the rating of the wide body DW version of the same die, and it is the code that fits where the creepage distance is already fixed by the enclosure. It meets ISO 11898-2, runs classic CAN at 1 Mbps, and has a 150 nanosecond typical loop delay.

Order code and package

Order codeISO1050DUBR
Functionisolated CAN transceiver
PackageSOIC, 8 pins, DUB body
Isolation2500 V RMS for one minute per UL 1577
Data rateclassic CAN to 1 Mbps
StandardISO 11898-2
Loop delay150 nanoseconds typical, 210 nanoseconds maximum
Bus fault protectionminus 27 V to plus 40 V
Transient immunity50 kV per microsecond typical
I/O supplysupports 3.3 V and 5 V controllers
Outputsfail-safe, dominant state on loss of input
Lifetime25 year typical at rated working voltage
Temperature rangeminus 55 to plus 105 C

Electrical parameters that decide the application

Barriersilicon dioxide capacitor, 2500 V RMS in this body
CertificationsVDE 0884-17, UL 1577, CSA for IEC 61010-1 and IEC 60601-1
Reinforced approvalTUV to EN, UL and CSA 62368-1 on the DW body only
ProtectionTXD dominant time out stops a stuck driver from blocking the bus
Fail-safeoutputs go dominant if the input is floating or the supply is lost
Bus pinsfault tolerant to minus 27 V and plus 40 V in the powered and unpowered state
Supply5 V on the bus side, 3.3 V or 5 V on the controller side
Data rate limit1 Mbps, set by the ISO 11898-2 physical layer, not by the barrier

Points to check before this part goes on a BOM

The 210 nanosecond maximum loop delay is the number to use for timing, not the 150 nanosecond typical figure. At 1 Mbps a bit is 1000 nanoseconds, so the worst case delay plus the controller sample point still leaves room, but a chain of two isolated nodes on one bus doubles that delay.

This body is rated 2500 V RMS while the DW body of the same die is rated 5000 V RMS. The die is the same, so the difference in a comparison table is the package creepage, and a board that needs reinforced insulation at mains voltage should be ordering the DW code rather than adding spacing around the DUB.

Fail-safe outputs go dominant when the input floats, which holds the bus in a known state during power up and stops a floating controller pin from generating random frames. That behaviour is a property of the part, and it does not replace the bias network a large multi-node bus still needs.

The bus fault rating of minus 27 V to plus 40 V is narrower than the 70 V of the newer ISO1042. On a 24 V industrial rail that is enough; on a 48 V battery rail a harness short exceeds it, and the ISO1042 is the code that survives that fault.

Where this order code fits

Motor drives, plc racks and isolated CAN ports on industrial boards order this code when the barrier has to fit an existing 8-pin footprint. Boards comparing it with a neighbouring part start from our CAN Bus Transceiver Selection page, and boards replacing a part that has gone end of life start from the Obsolete RF Part Replacement page.

Questions buyers ask

Does this part support CAN FD? No. It is a classic CAN transceiver limited to 1 Mbps by the physical layer; the FD capable part in the same family line is the ISO1042.

Can it run from a 3.3 V controller directly? Yes, the I/O side accepts 3.3 V and 5 V logic while the bus side runs from its own 5 V isolated supply.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.