ISO1042QDWVRQ1
Product Specifications
ISO1042QDWVRQ1
Texas Instruments — Power Management & Signal Chain
Product Overview
The ISO1042QDWVRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ISO1042QDWVRQ1: the automotive code in the eight pin body, with the seventy volt bus fault
ISO1042QDWVRQ1 is the automotive qualified code of the isolated controller area network transceiver in the eight pin SOIC body, the DWV package. It carries the same barrier as the sixteen pin version and the same electrical rows: 5000 volts of withstand, plus or minus 70 volts of bus fault tolerance, plus or minus 30 volts of bus common mode, and a loop delay of 152 nanoseconds.
The eight pin body is the one to choose where the board space is tight and the creepage requirement is met by the package footprint. The Q1 suffix means the part is released through the automotive flow, so the temperature range of minus 40 to plus 125 degrees and the qualification records travel with the code rather than being requested separately.
ISO1042QDWVRQ1 as the vendor document publishes it
| Function | isolated controller area network transceiver |
| Standard | ISO 11898-2:2016 physical layer |
| Data rate | 1 megabit per second classic, 5 megabits per second flexible data rate |
| Loop delay | 152 nanoseconds typical |
| Bus fault protection | plus or minus 70 volts direct current |
| Bus common mode range | plus or minus 30 volts |
| Bus pin discharge tolerance | plus or minus 16 kilovolts human body model |
| Logic side supply | 1.71 to 5.5 volts, 1.8 volt operation window 1.71 to 1.89 volts |
| Bus side supply | 2.25 to 5.5 volts |
| Logic side current | 2.3 to 3.5 milliamps with the driver idle |
| Withstand isolation | 5000 volts root mean square for 60 seconds |
| Maximum repetitive isolation | 1500 volts peak |
| Maximum transient isolation | 7071 volts peak |
| Clearance and creepage | greater than 8.5 millimetres |
| Temperature range | minus 40 to plus 125 degrees |
| Packages | 16 pin SOIC body DW, 8 pin SOIC body DWV |
| Catalogue code | ISO1042QDWVRQ1 |
| Qualification | automotive, AEC-Q100 flow |
| Package | 8 pins, SOIC body DWV |
| Temperature range | minus 40 to plus 125 degrees |
An isolated CAN transceiver that survives seventy volts on the bus
ISO1042QDWVRQ1 is an isolated controller area network transceiver with a silicon dioxide barrier between the logic side and the bus side. The bus pins withstand plus or minus 70 volts of direct current fault, plus or minus 16 kilovolts of human body model discharge, and the common mode range on the bus is plus or minus 30 volts, which is what a node on a long industrial bus actually sees.
It meets the ISO 11898-2:2016 physical layer standard, runs classic CAN at 1 megabit per second and CAN with flexible data rate at 5 megabits per second, and has a loop delay of 152 nanoseconds. The driver carries a dominant time out and both supplies carry undervoltage detection, so a stuck driver or a brown out cannot hold the bus down.
Five thousand volts of withstand, and the four numbers behind it
The isolation figures of ISO1042QDWVRQ1 are 5000 volts root mean square of withstand voltage for 60 seconds, 1500 volts peak of maximum repetitive isolation voltage, 7071 volts peak of maximum transient isolation voltage, and a working voltage of 1060 volts root mean square. The clearance and creepage across the package are both greater than 8.5 millimetres.
Those four numbers answer four different questions: the withstand figure is the type test, the repetitive peak is the life limit, the transient figure is the surge case, and the working voltage is what the barrier holds every day. A basic isolation part and a reinforced isolation part are both published in this family, and the difference is in the certification rather than in the silicon.
A hundred and fifty two nanoseconds of loop delay
The loop delay of ISO1042QDWVRQ1, driver input to receiver output, is 152 nanoseconds typical. That figure is what sets the maximum bus length at a given bit rate, because the arbitration round trip has to finish inside one bit time, and it is also why the part is published with a dominant time out rather than without one.
At 1 megabit per second a bit is 1000 nanoseconds, so a 152 nanosecond transceiver leaves most of the bit for cable propagation. At 5 megabits per second the bit is 200 nanoseconds and the loop delay is three quarters of it, which is the practical limit of the flexible data rate mode on a long bus rather than a limit of the transceiver.
Two supplies, and the side that has to be five volts
ISO1042QDWVRQ1 takes 1.71 to 5.5 volts on the logic side and 2.25 to 5.5 volts on the bus side, so a 1.8 volt controller can talk to a 5 volt bus without a level shifter. The logic side current is 2.3 to 3.5 milliamps with the driver idle, and the bus side draws whatever the terminated bus takes, up to the 70 milliamp class of a dominant driver.
The two supplies are not interchangeable: the bus side needs at least 2.25 volts to meet the ISO 11898-2 driver output, and the logic side can go as low as 1.71 volts only in the 1.8 volt operating window. A board that runs both sides from one 3.3 volt rail is inside both windows, which is the usual arrangement when the isolated supply is generated on the bus side.
Two packages, and the automotive code
The part is published in a sixteen pin wide body SOIC and in an eight pin SOIC, both with the same barrier and the same electrical rows; the eight pin version simply drops the duplicate supply pins. The temperature range is minus 40 to plus 125 degrees on both, and the automotive qualified code carries the Q1 suffix with the AEC-Q100 flow behind it.
The wide body is the one to choose when the creepage across the barrier has to survive a pollution degree 2 environment, because the eight pin body has less distance between the two sides. Both are moisture level 2 at 260 degrees, so the floor life is the same and the difference is the board space against the creepage.
Where an isolated CAN node belongs
ISO1042QDWVRQ1 belongs on a motor drive node that shares a bus with a controller at a different ground potential, on a battery management board that sits at the top of a stack, on an electric vehicle charger that has a mains side and a vehicle side, and on any inverter where the bus harness runs between cabinets.
The 70 volt bus fault and the 5000 volt barrier are the two rows that decide those cases. What the part does not do is supply the isolated power: the bus side needs its own 5 volt rail from an isolated converter, and that converter, not the transceiver, is normally the part that sets the cost and the board area of the node.
What the isolated node still has to buy
The transceiver is one of three parts on an isolated bus node. The second is the isolated supply that feeds the bus side, and the third is the termination and the protection on the bus itself. The transceiver protects its own pins to plus or minus 70 volts and to 16 kilovolts of discharge, and it does not protect the rest of the node from a surge that arrives on the harness.
The isolated supply normally sets the cost and the board area, because a 1 watt converter with 5000 volts of isolation is a larger part than the transceiver. That is why the eight pin body matters: it frees the space the converter needs, and the barrier rating, not the package, is what the two parts have to agree on.
The bus side supply and the isolated power are two separate purchases. Our CAN bus transceiver selection page covers the transceiver choice, and the traceability report page covers what travels with an automotive code.
Does the eight pin body reduce the isolation rating? No. The barrier and the 5000 volt withstand are the same, and the eight pin body simply drops the duplicate supply pins of the sixteen pin version, which changes the creepage rather than the barrier.
Can the transceiver run with both sides at 3.3 volts? Yes. The logic side accepts 1.71 to 5.5 volts and the bus side 2.25 to 5.5 volts, so a 3.3 volt rail on both sides is inside both windows.