Contact Us

INA849DR

Brand: Texas Instruments
Texas Instruments INA849DR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA849DR — Power Management & Signal Chain | Superb Automation

INA849DR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA849DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA849DR: 1 nanovolt instrumentation amplifier with 28 MHz bandwidth

INA849DR is an ultra low noise instrumentation amplifier with a 6 kiloohm gain network in a SOIC body of 8 pins. One nanovolt per root hertz of input noise, 35 microvolts of maximum offset and 28 MHz at unity gain, from a part whose gain equation uses a 6 kiloohm internal pair, 1 plus 6 kiloohms over RG, for a gain range of 1 to 10000. The supply runs from 8 V to 36 V single, so this is a plus and minus 4 V or wider part.

Order code and package

Order codeINA849DR
Functionultra low noise instrumentation amplifier
Gain1 to 10000, set by one external resistor
Gain equationG equals 1 plus 6 kiloohms divided by RG
PackageSOIC, 8 pins
Other bodies8 pin VSSOP
Supply8 V to 36 V single, plus and minus 4 to 18 V
Noise1 nanovolt per root hertz typical
Bandwidth28 MHz at gain 1, 13 MHz at gain 10, 8 MHz at gain 100
Slew rate35 volts per microsecond
Offset voltage35 microvolts maximum
DatasheetSBOS945 revision B

Electrical parameters that decide the application

Offset drift0.4 microvolts per C maximum
Input bias current20 nanoamps maximum, the cost of the super beta input stage
Gain drift5 ppm per C at gain 1
Settling0.001 percent, which is what a 16 bit acquisition needs
Supply minimum8 V, so a single 5 V rail is not enough
Gain span1 to 10000 with a 6 kiloohm internal pair
Bandwidth at gain 10001.25 MHz, still wide for a gain that high
Outputrail to rail within the supply
Temperature rangeminus 40 to plus 125 C
Noise at gain 11 nanovolt per root hertz, below the thermal noise of most sources

Points to check before this part goes on a BOM

One nanovolt per root hertz is below the thermal noise of a 50 ohm source, so the source decides the noise floor and not the amplifier. Buying this part for a 10 kiloohm source is buying a number that the resistor beside it makes irrelevant.

Twenty nanoamps of input bias current is the price of the low noise input stage. Into a 100 kiloohm source that is 2 millivolts of offset, which is fifty times the amplifier's own offset voltage; the source impedance has to be low for this part to make sense.

The 8 V supply minimum is a hard constraint that rules out every 5 V and 3.3 V board. This is a plus and minus 5 V or wider system, and the gain network's 6 kiloohm pair is part of why the supply cannot go lower.

Six kiloohms rather than 50 kiloohms is what allows 28 MHz at unity gain and 1.25 MHz at gain 1000. The resistor that sets the gain is also smaller, so its parasitic capacitance and its tolerance matter more than they would on a 50 kiloohm part.

Thirty five volts per microsecond and 0.001 percent settling are the two figures a multiplexed acquisition system checks first. A 16 bit converter sampling at 500 kilohertz needs both, and the settling figure is the one that decides whether channel to channel crosstalk appears.

Gain drift of 5 ppm per C at unity is quoted without a second figure for higher gains in the front page table. The external resistor still sets the gain, so its coefficient has to be added by the buyer rather than read from the document.

Where this order code fits

Photodiode front ends, low impedance strain gauges and any measurement where the source is quieter than the amplifier are the users of this order code. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can it run from a single 5 V supply? No. The minimum supply is 8 V, so the board needs a plus and minus 4 V rail at least, which is why this part appears in bench instruments more often than in 5 V systems.

Is a 1 nanovolt amplifier the right choice for a high impedance sensor? No. Bias current of 20 nanoamps into a high impedance source creates more error than the noise saves, so the low noise stage suits a low impedance source.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.