Contact Us

INA828ID

Brand: Texas Instruments
Texas Instruments INA828ID is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA828ID — Power Management & Signal Chain | Superb Automation

INA828ID

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA828ID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA828ID: 50 microvolt instrumentation amplifier and second generation INA128

INA828ID is a precision instrumentation amplifier positioned as the successor to the INA128 in a SOIC body of 8 pins. The document presents it as the second generation of the INA128 with the same pinout and a tighter specification: 50 microvolts of maximum offset, 7 nanovolts per root hertz of noise, 2 MHz at unity gain and stability into 1 nanofarad. One resistor sets the gain with the 1 plus 50 kiloohm over RG relation.

Order code and package

Order codeINA828ID
Functionprecision instrumentation amplifier
Gain1 to 1000, set by one external resistor
Gain equationG equals 1 plus 50 kiloohms divided by RG
PackageSOIC, 8 pins
Supply4.5 V to 36 V single, plus and minus 2.25 to 18 V
Supply current650 microamps maximum
Input protectionplus or minus 40 V beyond the rails
Noise7 nanovolts per root hertz
Bandwidth2 MHz at gain 1, 260 kHz at gain 100
DatasheetSBOS853 revision A

Electrical parameters that decide the application

Offset voltage50 microvolts maximum
Gain drift5 ppm per C at gain 1, 50 ppm per C above gain 1
Common mode rejection110 dB minimum at gain 10
Power supply rejection100 dB minimum at gain 1
Load stability1 nanofarad without a series resistor
Temperature rangeminus 40 to plus 125 C
Outputrail to rail with a reference pin
Input stageprotected to 40 volts beyond either rail
Family positionsecond generation of the INA128, same pinout
Gain drift above unity50 ppm per C, which is higher than the 35 ppm of its siblings

Points to check before this part goes on a BOM

Fifty ppm per C of gain drift above unity is worse than the 35 ppm of the wideband parts in the same catalogue. The tighter offset and the lower noise come with a slightly looser gain drift term, so a board that depends on gain stability should compare both rows.

Seven nanovolts per root hertz at gain 100 with 110 dB of rejection is the combination a medical front end wants. It is also why the supply current is 650 microamps rather than the 200 of the low power parts.

The part is presented as the successor to the INA128 and the pinout matches, so a board can be reworked without a new board. The gain equation uses the same 50 kiloohm pair, which keeps the existing resistor value valid.

Stability into 1 nanofarad removes the series resistor that older instrumentation amplifiers needed at a converter input. On a board where the amplifier sits 10 millimetres from the converter, that resistor was the part that spoiled the settling.

Forty volts of input protection is the industrial number, not the field cable number. A 24 V loop miswired onto this part survives; a 48 V loop does not, and the parts with 60 volt inputs are the ones to specify there.

The 4.5 V supply minimum keeps it off a 3.3 V rail. Boards that need this accuracy on a 3.3 V rail have to boost the supply or accept the lower common mode range of a current sense part.

Where this order code fits

Boards carrying an INA128 that need a tighter offset without changing the footprint are the obvious callers, along with new medical and test front ends. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is it pin compatible with the INA128? Yes. The document presents it as the second generation of that part with the same pinout and the same gain equation, so an existing board can carry it without a board change.

Does the tighter offset come with a penalty? Gain drift above unity is 50 ppm per C where sibling parts hold 35, and the supply current is 650 microamps, so the tighter offset is paid for in those two rows.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.