Contact Us

INA826AID

Brand: Texas Instruments
Texas Instruments INA826AID is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA826AID — Power Management & Signal Chain | Superb Automation

INA826AID

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA826AID from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA826AID: 200 microamp instrumentation amplifier with a rail to rail output

INA826AID is a low power instrumentation amplifier with a rail to rail output stage in a SOIC body of 8 pins. The input common mode range includes the negative rail, the output swings to both rails, and the supply current is 200 microamps, all from a 3 V to 36 V supply. One resistor sets the gain with the 1 plus 49.4 kiloohm over RG relation, and the inputs take 40 volts beyond the rails without damage.

Order code and package

Order codeINA826AID
Functionlow power instrumentation amplifier
Gainset by one external resistor, 1 plus 49.4 kiloohms over RG
PackageSOIC, 8 pins
Other bodies8 pin VSSOP and 8 pin WSON
Supply3 V to 36 V single, plus and minus 1.5 to 18 V
Supply current200 microamps
Input common modeincludes the negative rail
Input protectionplus or minus 40 V beyond the rails
Outputrail to rail
Bandwidth1 MHz at gain 1, 60 kHz at gain 100
DatasheetSBAS435 revision D

Electrical parameters that decide the application

Offset voltage150 microvolts maximum
Gain drift1 ppm per C at gain 1, 35 ppm per C above gain 1
Common mode rejection104 dB minimum at gain 10, 100 dB at 5 kHz
Power supply rejection100 dB minimum at gain 1
Noise18 nanovolts per root hertz at gains of 100 and above
Temperature rangeminus 40 to plus 125 C
Input bias currentspecified for a bridge source with a return path to ground
Output swingwithin tens of millivolts of each rail at light load
Stabilitystable into a capacitive load with a small series resistor
Family positionthe low supply current, rail to rail output member of the 49.4 kiloohm line

Points to check before this part goes on a BOM

An input range that includes the negative rail is what lets a single supply board read a ground referenced bridge. Most instrumentation amplifiers need the input lifted above ground, and that lift costs a reference and two resistors that this part does not need.

The 150 microvolt maximum offset is ten times the typical figure of the wideband parts and it is the price of the rail to rail input stage. On a 350 ohm bridge with a 2 millivolt span, that offset is 7 percent of full scale before any gain.

Gain drift of 1 ppm per C at unity jumps to 35 ppm per C once the external resistor sets the gain. The jump is the resistor, and a 25 ppm per C resistor makes the total drift worse than the datasheet row.

Sixty kilohertz at gain 100 is enough for a temperature loop and not for a dynamic measurement. A flow meter with a 1 kilohertz vortex signal has margin, a vibration channel with 20 kilohertz does not.

Two hundred microamps of supply current at 3 V is 600 microwatts, which is what a loop powered transmitter can spend on its front end. The converter behind it usually wants more than the amplifier, so the budget has to be split before the parts are chosen.

The rail to rail output is quoted at light load. Driving a 10 kiloohm converter input holds the swing, and driving a 1 kiloohm load pulls the top of the range in by tens of millivolts, which matters on a 12 bit converter.

Where this order code fits

Analog input modules, flow transmitters and battery test channels are the usual boards, where the signal sits near ground and the supply is a single 5 V rail. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Can it read a bridge with one side at ground? Yes. The input common mode range includes the negative rail, which is the case this part was built for; the reference pin then sets where zero load appears at the output.

Is 150 microvolts of offset a maximum or a typical? It is a maximum, and the typical is lower; a project that needs tighter offset moves to the wideband parts in this line rather than trimming this one.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.