INA823DT
Product Specifications
INA823DT
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA823DT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA823DT: the low power precision part on a 250 piece reel
INA823DT is the low power precision instrumentation amplifier in the 8 pin SOIC on a 250 piece small reel. It draws 180 microamps typical and holds 20 microvolts typical and 100 microvolts maximum of offset, with 8 nanoamps maximum of bias current, from a supply range that starts at 2.7 volts and reaches 36.
The 250 piece reel is the carrier for a first build, and the part is the one to reach for when a channel has to be both quiet on current and accurate on offset: a 4 to 20 milliamp transmitter, a battery field meter or a ground referenced current sense whose input sits slightly below the negative rail. The input extends 150 millivolts below that rail and survives 60 volts beyond the supplies.
INA823DT as the vendor document publishes it
| Offset voltage | 20 microvolts typical, 100 microvolts maximum |
| Offset drift | 0.1 microvolts per degree typical, 0.4 maximum |
| Input bias current | 8 nanoamps maximum |
| Gain equation | 1 plus 100 kilo-ohms divided by the gain resistor |
| Gain range | 1 to 10 000 V/V |
| Common mode rejection at a gain of 1 | 84 dB minimum |
| Common mode rejection at a gain of 10 | 104 dB minimum |
| Common mode rejection at a gain of 100 and above | 120 dB minimum |
| Power supply rejection at a gain of 1 | 100 dB minimum |
| Input stage voltage noise | 21 nanovolts per root hertz at 1 kHz |
| Output stage voltage noise | 120 nanovolts per root hertz at 1 kHz |
| Current noise | 160 femtoamps per root hertz at 1 kHz |
| Input voltage below the negative rail | 150 millivolts |
| Input protection | 60 volts beyond the supply rails |
| Supply current | 180 microamps typical |
| Supply range | 2.7 to 36 volts single, plus or minus 1.35 to plus or minus 18 volts dual |
| Output | rail to rail |
| Temperature range | minus 40 to plus 125 degrees |
| Vendor status | active, 250 piece small reel |
| Catalogue code | INA823DT |
| Vendor string | INA823DT |
| Lead finish | NIPDAU |
| Moisture level | level 2, 260 degrees, one year floor life |
Fifteen hundred millivolts below the negative rail
The input voltage of INA823DT extends 150 millivolts below the negative supply, and the inputs are protected to 60 volts beyond the rails. That combination covers the two failure modes of an industrial front end: a sensor whose common mode sits slightly under ground, and a field line that is shorted to a 24 volt source while the module is powered.
Running below the negative rail is what a current sense on a ground referenced shunt needs, because the shunt sits at ground and the amplifier's own offset plus the cable drop can put the input a few tens of millivolts negative. The protection is the other half: 60 volts of overvoltage with the input current limited to a safe level means an unplugged transducer cable does not take the module with it, and it means a 24 volt field line can be wired to the input by mistake without a destructive result.
A hundred and eighty microamps with a precision offset
INA823DT draws 180 microamps typical, which puts it in the low power class, and still holds 20 microvolts typical and 100 microvolts maximum of offset with 8 nanoamps maximum of bias current. The supply range covers a 3.3 volt rail and a plus or minus 15 volt analogue front end with the same part.
That combination is unusual enough to be the reason to buy it. A part that draws under two hundred microamps is normally a CMOS stage with a millivolt of offset; a part with 100 microvolts of offset normally draws milliamps. The rows that constrain it are the rejection at unity gain and the industrial temperature range, so an under hood module still needs a different code.
Rejection that improves with gain
The common mode rejection of INA823DT is 84 dB minimum at unity gain, 104 dB minimum at a gain of 10 and 120 dB minimum at a gain of 100 and above. The power supply rejection is 100 dB minimum at unity gain. That shape is the signature of a three op amp instrumentation amplifier: the input stages run at unity and their errors are divided by the gain of the following stage.
The practical consequence is that a channel which needs rejection should be run at the highest gain the signal allows, because the rejection comes with the gain rather than with a different part. On a 10 millivolt bridge at a gain of 100, the 120 dB figure turns a 10 volt common mode into 10 microvolts at the input, which is under the maximum offset. At unity gain on the same 10 volt common mode the 84 dB figure gives 630 microvolts, which is six times the offset and the dominant error.
Twenty one nanovolts, and the gain resistor
The voltage noise of INA823DT is 21 nanovolts per root hertz, which is above the 8 nanovolts of the low noise family members and below what a general purpose amplifier delivers, and the bias current of 8 nanoamps maximum makes it usable on a source of tens of kilo-ohms rather than megohms.
The gain is 1 plus 100 kilo-ohms divided by one external resistor, from 1 to 10 000, so the network that decides the accuracy is a single component. That is convenient and it is also the largest error term: the internal network is trimmed, and the external resistor is not. A 0.1 per cent resistor with 25 ppm per degree sets a 0.1 per cent channel, and a 1 per cent resistor sets a 1 per cent channel, which is the range of accuracy a part at this price is normally asked for.
The supply range and the two rails
INA823DT runs from a single supply in the low voltage range up to 36 volts, or from a dual supply, which is the row that lets one part serve a 3.3 volt logic board and a plus or minus 15 volt analogue card. The output is rail to rail, so the swing is set by the converter behind the part rather than by the amplifier.
The specified temperature range is minus 40 to plus 125 degrees, with the offset and rejection rows guaranteed over that window. A channel that runs at 105 degrees in an enclosure therefore does not need a margin calculation beyond the drift row, and the bias current of 8 nanoamps over 165 degrees is the row to check on a high impedance source: 8 nanoamps into 100 kilo-ohms is 800 microvolts, which is eight times the maximum offset and the real limit of the channel.
Where the low power precision part fits
INA823DT fits a battery powered field instrument, a 4 to 20 milliamp transmitter with a small budget for the front end, a ground referenced current sense that needs the input to run slightly below the negative rail, and an industrial input module where a 60 volt field fault has to be survived.
It stops where the signal is a thermocouple, because 100 microvolts of maximum offset against a 40 microvolt per degree output needs an auto-corrected stage. It stops where the common mode is a 48 volt bus, because the protection is a fault rating rather than an operating range. And it stops where the channel has to hold its gain over temperature with a 1 per cent resistor, because the resistor sets the drift. Our amplifier cross reference page covers the parts either side of this one, and the BOM scrubbing page covers the gain resistor against the bill of materials.
The current draw and the input window are the two rows this part is bought on. Our amplifier cross reference page covers the parts either side of this one, and the BOM scrubbing page covers the gain resistor against the bill of materials.
What is the supply floor? 2.7 volts single, so a 3.3 volt rail with a 10 per cent tolerance is inside the range.
Can the input go below ground? Yes, 150 millivolts below the negative rail, which is what a ground referenced shunt needs.