INA823DR
Product Specifications
INA823DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA823DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA823DR: 180 microamp instrumentation amplifier with 60 volt input protection
INA823DR is a micro power instrumentation amplifier with a wide input range in a SOIC body of 8 pins. One hundred and eighty microamps of supply current, 20 microvolts of typical offset and inputs that take 60 volts beyond either rail, running from 2.7 V to 36 V on a single supply. One resistor sets any gain from 1 to 10000 with the 1 plus 100 kiloohm over RG relation, which is the widest gain span in this line.
Order code and package
| Order code | INA823DR |
| Function | micro power instrumentation amplifier |
| Gain | 1 to 10000, set by one external resistor |
| Gain equation | G equals 1 plus 100 kiloohms divided by RG |
| Package | SOIC, 8 pins |
| Other bodies | 8 pin VSSOP |
| Supply | 2.7 V to 36 V single, plus and minus 1.35 to 18 V |
| Input protection | plus or minus 60 V, and 150 millivolts below the negative rail |
| Supply current | 180 microamps typical |
| Noise | 21 nanovolts per root hertz |
| Bandwidth | 1.9 MHz at gain 1, 60 kHz at gain 100 |
| Datasheet | SBOS859 revision B |
Electrical parameters that decide the application
| Offset voltage | 20 microvolts typical, 100 microvolts maximum |
| Input bias current | 8 nanoamps maximum |
| Common mode rejection | 84 dB at gain 1, 104 dB at gain 10, 120 dB at gain 100 and above |
| Power supply rejection | 100 dB minimum at gain 1 |
| Load stability | 1 nanofarad without a series resistor |
| Gain span | 1 to 10000, the widest in this family |
| Temperature range | minus 40 to plus 125 C |
| Input range below ground | 150 millivolts below the negative rail, which is what a loop powered part needs |
| Noise penalty | 21 nanovolts per root hertz against 7 to 8 in the wideband parts |
| Output | rail to rail with a reference pin |
Points to check before this part goes on a BOM
The 100 microvolt maximum offset is the honest figure and the 20 microvolts is typical. A transmitter that quotes the typical number in its accuracy budget is overstating what a production unit will do across temperature.
Measuring 150 millivolts below the negative rail is a loop powered requirement, not a luxury. A shunt in the return leg of a 4 to 20 milliamp loop sits below the local ground, and an amplifier that clips there cannot read the low end of the span.
Twenty one nanovolts per root hertz is three times the noise of the wideband parts, and the trade is explicit. The low supply current buys noise, so a build with a 10 microvolt signal and a 1 kilohertz bandwidth has to check whether the amplifier noise or the source resistance is the limit.
Gain to 10000 is unusual and it is what a thermocouple or a strain gauge needs. At gain 10000 the closed loop bandwidth falls to a few kilohertz, which is fine for a temperature loop and hopeless for a vibration channel.
Eighty four dB of rejection at unity gain is the weakest point of the table. A board that runs this part at gain 1 with a 5 V common mode and a 3.3 V output range is relying on a term that is 36 dB worse than at gain 100.
The supply range starts at 2.7 V, which puts this part on a 3.3 V rail without a charge pump. That is the single reason it appears in 3.3 V industrial boards where the 4.5 V parts cannot go.
Where this order code fits
Loop powered transmitters and battery instruments are the boards that use it, because the 180 microamp budget is what a 4 to 20 milliamp loop can afford. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.
Questions buyers ask
Is the 60 volt protection rated for continuous overvoltage? It is a survival rating for faults; a continuous 60 volts beyond the rail is a thermal question for the input stage, so the source still needs a series resistor or a fuse.
Why is the offset maximum so much wider than the typical? The part is trimmed to a typical figure and tested to a maximum of 100 microvolts; a budget that has to hold over production uses the maximum, not the typical.
SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.