INA823DGKR
Product Specifications
INA823DGKR
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA823DGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA823DGKR: a 2.7 V instrumentation amplifier with 180 uA of supply current
The INA823DGKR is a precision instrumentation amplifier in an 8 pin VSSOP that runs from a 2.7 V single supply up to 36 V, or a dual supply to plus and minus 18 V, on 180 uA typical. That combination is what makes it a battery instrument part: a 3.3 V rail is enough headroom for the amplifier, and the current is low enough that the front end does not dominate the power budget.
Offset is 20 uV typical and 100 uV maximum, input bias current is 8 nA maximum, and the common mode rejection is 84 dB minimum at unity gain, 104 dB at a gain of 10 and 120 dB at a gain of 100 or more. The input voltage range extends 150 mV below the negative supply, which is what allows a single supply part to measure a signal that touches ground without a charge pump, and the inputs are protected to 60 V against an unpowered sensor.
Key data for the INA823DGKR
| Gain | 1 to 10,000 set by one external resistor between the two RG pins |
| Offset and bias | 20 uV typical and 100 uV maximum offset, 8 nA maximum input bias current |
| Rejection | 84 dB minimum at unity gain, 104 dB at a gain of 10, 120 dB at a gain of 100 and above, 100 dB power supply rejection at unity gain |
| Noise and bandwidth | 21 nV per root hertz input noise, 1.9 MHz at unity gain and 60 kHz at a gain of 100, stable into 1 nF |
| Input range | Extends 150 mV below the negative supply, with 60 V protection on both inputs |
| Supply | 2.7 V to 36 V single or 1.35 V to 18 V dual, 180 uA typical supply current, minus 40 C to 125 C |
Body, marking and reel data
| Body | DGK, 8 pin VSSOP at 3.00 mm by 3.00 mm; the family also ships an 8 pin SOIC at 4.90 mm by 3.91 mm |
| Reel | R suffix is the large reel; the VSSOP is the smaller of the two footprints and the one used where board area is tight |
| Gain resistor | One external resistor, so a gain change is a BOM change on that resistor rather than a new amplifier |
| Protection | 60 V on both inputs, which is well above the 36 V maximum supply and covers a transducer that is powered separately |
| Document | SBOSA75B dated July 2021 and revised November 2021 |
Where a 2.7 V instrumentation amplifier changes the power tree
The usual reason an engineer reaches for this part is that the rest of the board runs at 3.3 V. A precision instrumentation amplifier that needs 4.5 V or more forces a boost converter or a charge pump, and both add noise that the front end then has to reject. The INA823 runs from the same 3.3 V rail as the converter and the microcontroller, which removes a switching supply from the analog domain entirely.
The 150 mV below the negative rail is the second reason. A thermocouple or a bridge that is referenced to ground will swing slightly negative on a cold junction or a reverse strain, and an amplifier that stops at ground clips the signal and changes its own offset during the excursion. The INA823 stays linear through that window, so the reading is valid at zero and at small negative values rather than only above a threshold.
The 60 V protection decides how much external circuitry the front end needs. A sensor that is connected through a connector can be hot plugged, and the amplifier can be powered while the sensor is not. With protection inside the part, a 1 k series resistor and a small capacitor are enough to meet a typical surge requirement, and those parts are small enough that they do not add measurable noise at 21 nV per root hertz. Our amplifier cross reference compares this part against the lower noise INA819 and the wider bandwidth INA849, and the medical device components note covers the same front end in portable monitors where the 2.7 V supply and the 8 nA bias are the deciding rows.
Buyer questions on the INA823DGKR
Can it drive a 3.3 V converter directly? Yes, the output swings inside the supply, and at a gain of 10 the bandwidth of 270 kHz is far above what a 10 kSPS converter needs.
What gain resistor gives 10 V/V? The value comes from the gain equation in the document and sits in the low kilo ohm range for a gain of 10; a 0.1 per cent part keeps the gain error below the amplifier's own 0.02 per cent class.
Is 8 nA of bias current low enough for a pH probe? A pH probe has an impedance in the hundreds of megohms, where 8 nA produces a large error, so that application needs a CMOS input part rather than this one.
Availability and ordering notes
INA823DGKR is the VSSOP-8 member of the family, and the SOIC-8 body is a separate order code with a different footprint. The part is a 2021 release with a current revision, and it sits in the same family as the INA819 and INA849, so a customer choosing between the three is choosing on supply voltage, noise and bandwidth rather than on availability.