REF192ESZ-REEL7
Product Specifications
REF192ESZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The REF192ESZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
REF192ESZ-REEL7: 2.500 V From a Supply Only 100 mV Higher, and the 93 Codes It Costs at 16 Bits
The REF192ESZ-REEL7 is the 2.500 V member of the REF19x family in an 8-lead SO package. Initial accuracy is plus or minus 2 mV maximum, temperature coefficient 5 ppm per degree Celsius maximum, supply current 45 uA maximum with 15 uA in sleep, load regulation 4 ppm per mA, line regulation 4 ppm per V, 30 mA of output current with short circuit protection, and a dropout low enough for a supply 100 mV above the output. The series is specified over minus 40 to plus 85 degrees Celsius with typical performance to plus 125 degrees. The SO-8 body carries every electrical grade, while the PDIP and TSSOP carry the lowest grade only, and the part is also available in die form.
A 2.5 V reference is what a converter uses when its input range is plus or minus 2.5 V, or when the analogue rail is 3.3 V and there is no room for a 4.096 V reference. It halves the full scale of a converter compared with a 5 V reference, which doubles the size of every step, and that is the trade to be clear about before choosing it.
2 mV is 52 codes at 16 bits, the largest relative error of the three REF19x voltages we carry
One 16-bit step at 2.500 V is 38.15 uV, so plus or minus 2 mV of initial accuracy is 52 codes each way. Five ppm per degree Celsius over 125 degrees is 625 ppm, 1.5625 mV or 41 codes. Together the reference moves 3.56 mV, which is 93 codes, and that is the largest share of a 16-bit range among the 2.5 V, 4.096 V and 5.0 V parts, simply because the same millivolt error is a bigger fraction of a smaller full scale.
The minimum supply is 2.600 V, so a 3.3 V rail at minus 5 percent, which is 3.135 V, leaves 535 mV of headroom. That is the reason this part is common on 3.3 V boards: it is the reference that fits, not the one with the best relative accuracy.
Halving the full scale doubles the step, and that is the whole decision
A 16-bit converter on 2.5 V has a 38.15 uV step, and on 4.096 V it has a 62.5 uV step. The 4.096 V option gives more absolute resolution for the same converter, and the 2.5 V option fits a 3.3 V analogue rail. If the signal is a plus or minus 1 V sensor output with a differential amplifier in front, the extra range of the 4.096 V reference is not used and the 2.5 V part is the better match. If the signal fills the converter, the larger full scale is worth the rail change.
The load regulation of 4 ppm per mA is 300 uV at the 30 mA output rating, about 8 codes. The output stage is there to feed a bridge or a resistor ladder directly, and the 45 uA supply current is what makes it possible to leave the reference on in a battery instrument without measuring it in the current budget.
Die form and the grade table
The part is available as die, which matters for a hybrid or a multichip module where the reference is bonded next to the converter. The grade letters select tolerance from the data sheet table, so the E suffix is a grade and not a package, and the family headline of plus or minus 2 mV describes the series rather than every order code.
Sleep mode at 15 uA is 131 mAh over a year if it is never turned off, well under the self discharge of any cell. The SLEEP pin takes a TTL or CMOS level, so a processor in standby can hold it off with a pin that is guaranteed low.
| Function | 2.500 V precision band gap voltage reference |
| Initial accuracy | Plus or minus 2 mV maximum, 52 codes at 16 bits |
| Temperature coefficient | 5 ppm per degree Celsius maximum, 1.5625 mV over 125 degrees |
| Total error | About 3.56 mV, 93 codes at 16 bits |
| Minimum supply | 2.600 V, leaving 535 mV on a 3.3 V rail at minus 5 percent |
| Load regulation | 4 ppm per mA, 300 uV at the 30 mA rating |
| Supply current | 45 uA maximum, 15 uA in sleep |
| Output current | 30 mA with short circuit protection |
| Package | 8-lead SO, order code ESZ-REEL7, also available as die |
| Lifecycle | In production at the vendor |
Two questions buyers ask
Why does the same family have three different error figures in codes?
Because the millivolt error is roughly the same and the full scale is not. Two millivolts is 52 codes at 2.5 V, 32 codes at 4.096 V and 26 codes at 5.0 V. The part with the lowest code count is not automatically the best choice, since it also needs the highest supply headroom, and the 5 V part cannot run from a 5 V rail at all.
Can the reference drive a 30 mA bridge directly?
It can, and the load regulation of 4 ppm per mA means the bridge current modulates the excitation by 120 ppm at full output. A 350 ohm bridge at 2.5 V draws 7 mA, which is 28 ppm, about 70 uV, and that is a systematic error in the measurement that a ratiometric converter arrangement cancels and an absolute one does not.
Ordering and supply
The ESZ suffix is the SO-8 body with the reel and the PBF suffix is the lead free finish. The family spans 2.5 V, 3.0 V, 4.096 V and 5.0 V, and the through hole and TSSOP bodies carry only the lowest grade.
We hold this reference for instrumentation and sensor builds. The analog mixed signal ICs page lists the references we carry, ADC and DAC cross reference is where the converter and the reference are compared as a pair, and where a reference is being replaced on an existing footprint, pin to pin cross reference covers the pin compatible alternatives.
Request Quote — In Stock, 100% New & Original, Full Warranty