Contact Us

INA597IDR

Brand: Texas Instruments
Texas Instruments INA597IDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA597IDR — Power Management & Signal Chain | Superb Automation

INA597IDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA597IDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA597IDR: unity gain difference amplifier in a 8-pin SOIC

INA597IDR is a unity gain difference amplifier in a single ended output stage in a SOIC body of 8 pins. Unity gain, 200 microvolts of offset, 88 dB of rejection and a 2 MHz gain bandwidth product in a SOIC body. The part takes a differential signal, rejects what is common to both inputs, and presents it referred to a pin, which is the block a shunt front end or a line receiver needs when no gain is wanted.

Order code and package

Order codeINA597IDR
Functionunity gain difference amplifier
Gain1 V/V
PackageSOIC, 8 pins
Other bodies8 pin VSSOP and 10 pin VSON
Supply4.5 V to 36 V single, plus and minus 2.25 to 18 V
Offset voltage200 microvolts maximum
Common mode rejection88 dB minimum
Bandwidth2 MHz gain bandwidth product
Slew rate18 volts per microsecond
Temperature rangeminus 40 to plus 125 C
DatasheetSBOS385 revision B

Electrical parameters that decide the application

Offset drift5 microvolts per C maximum
Gain error0.03 percent maximum
Noise18 nanovolts per root hertz at 1 kHz
Quiescent current1.1 milliamps per amplifier
Load drive500 picofarads
Input impedanceset by the internal network
Outputsingle ended, referred to the reference pin
Common mode rangereaches the supply rails through the internal divider
Settlinglimited by the 2 MHz product at unity gain
Comparisonunity gain with a wider offset budget than the two ratio version

Points to check before this part goes on a BOM

Unity gain means the input range is the output range, and that is the constraint on a 3.3 V converter. A differential signal larger than the converter's reference has to be attenuated before this part, because there is no gain of one half on this order code.

Two hundred microvolts of offset is five times the two ratio version. On a 10 milliohm shunt that is 20 milliamps of reading error, which pushes the part towards a signal that is already large rather than towards a current sense front end.

Drift of 5 microvolts per C is 625 microvolts across the full range, three times the initial offset. A production trim at room temperature leaves that term in place, so a hot board reads differently from the unit that was signed off on the bench.

The internal divider sets the input impedance, so the source must be low impedance. A shunt qualifies, a piezo element does not, and a resistive divider in front of the part changes the rejection ratio because the divider's tolerances land directly on the difference.

1.1 milliamps per amplifier is the supply cost of the internal network. A four channel board pays 4.4 milliamps for four unity gain difference stages, which is ten times what a single supply current sense amplifier of similar accuracy draws.

The 4.5 V minimum supply rules out a 3.3 V rail. A board that runs the analogue section on 3.3 V needs a charge pump or a different part, and the current sense amplifier family covers that rail without one.

Where this order code fits

Motor current shunts, industrial line receivers and instrumentation front ends that only need the differential to single ended conversion are the boards that specify it. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Why buy unity gain rather than the two ratio version? When no attenuation is needed and the extra pin strap is a liability; the trade is a wider offset budget of 200 microvolts against 40.

Can it be used with a 5 V single supply? Yes. The single supply range starts at 4.5 V, so 5 V is inside it, with the common mode range reaching the rails through the internal divider.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.