Contact Us

INA500AIDBVR

Brand: Texas Instruments
Texas Instruments INA500AIDBVR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA500AIDBVR — Power Management & Signal Chain | Superb Automation

INA500AIDBVR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA500AIDBVR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA500AIDBVR: a difference amplifier with matched resistors and a 1.08 megohm input

The INA500AIDBVR is the unity gain member of the INA500 family, a difference amplifier that puts an operational amplifier and a matched resistor network in one 6 pin SOT-23. The A version is gain 1 with a 1.08 megohm input resistor, the B version is gain 0.5 with 1.44 megohm and the C version is gain 0.25 with 1.68 megohm, so the three parts cover attenuation as well as buffering.

The input impedance is the reason the part exists. A discrete difference amplifier built from an operational amplifier and four resistors has an input impedance set by those resistors, and a 10 k network loads a high impedance source. The INA500 moves that to above 1 megohm, which lets it sit directly on a battery stack tap or a resistive divider without changing the divider ratio. Supply current is 13.5 uA and the supply range is 1.7 V to 5.5 V, so the part can run from the same rail as a low power converter.

Key data for the INA500AIDBVR

GainUnity on the A version, 0.50 on B and 0.25 on C, each set by the internal resistor network rather than by external parts
Input impedanceAbove 1 megohm, with 1.08 megohm input resistors on the A version
Common modeUp to 27.5 V in the gain 0.25 version with a 5.5 V supply, and 13.75 V with a 2.75 V supply, which is the range that covers a multi cell battery tap
AccuracyCommon mode rejection 87 dB typical and 75 dB minimum, gain error 0.05 per cent maximum, offset 3.5 mV maximum referred to the output at unity gain
Speed125 kHz typical bandwidth, stable with a 200 pF load at under 20 per cent overshoot
Supply1.7 V to 5.5 V single rail or 0.85 V to 2.75 V dual, 13.5 uA typical quiescent current, minus 40 C to 125 C

Body, marking and reel data

BodyDBV, 6 pin SOT-23 at 2.9 mm by 2.8 mm; the family also ships SC70-6 at 2.1 mm by 1.25 mm and X2SON-6 at 1 mm by 0.8 mm
ReelR suffix is the large reel; the X2SON body is the one that needs a paste stencil check before a first article
PinsIN plus, IN minus, OUT, REF, V plus and V minus; the reference pin sets the output offset, so a level shift costs one divider
GradeA, B and C are separate order codes with different internal resistors, so a gain change is a part change and not a resistor change
DocumentSBOSAI9B dated December 2023 and revised March 2024, a current revision rather than a legacy one

Where an integrated difference amplifier replaces four resistors

The obvious application is a battery tap: a cell at 18 V in a stack has to be read by a 3.3 V converter, and a divider alone would load the cell. The INA500 in the gain 0.25 version accepts 27.5 V of common mode on a 5.5 V supply and attenuates by four, so an 18 V tap becomes 4.5 V, which still needs a further division but no longer loads the tap. The matched internal resistors keep the rejection at 87 dB typical, which is 20 dB better than a 1 per cent discrete network delivers.

The second application is current sensing on a high side shunt where the common mode is above the amplifier supply but below 27.5 V. The INA500 is not a current sense amplifier, so its offset and drift are not specified to the standard of the INA293 family, and it should not be used where a 12 uV offset matters. It is a level translator and a buffer with a known gain, and that is what the offset row says: 3.5 mV maximum referred to the output at unity gain.

The third application is replacing a discrete difference amplifier that was built from a commodity operational amplifier and four 0.1 per cent resistors. That substitution removes three placements, removes the resistor matching from the incoming inspection, and removes the tolerance stack that made the original circuit's rejection unpredictable. Our amplifier cross reference separates the difference amplifiers from the current sense amplifiers, and the medical device components note covers the same substitution in patient monitors where the input impedance has to stay high.

Buyer questions on the INA500AIDBVR

Can the gain be changed with external resistors? No. The gain is fixed by the internal network and the version letter, so a different gain means a different order code. That is the trade for the matching.

Is the 27.5 V common mode rating available at unity gain? No, the highest common mode belongs to the gain 0.25 version because the internal divider attenuates before the amplifier sees the signal. At unity gain the common mode window is narrower.

What happens with a 200 pF load? The part is specified to drive it with under 20 per cent overshoot. A heavier load, such as a long cable into a converter, needs a series resistor and should be checked on the bench.

Availability and ordering notes

INA500AIDBVR is the unity gain member in the 6 pin SOT-23. The three gain versions share the body and the pinout but not the internal resistors, so a purchase order has to name the letter. Because the part is a 2023 release, catalogue stock and distributor stock can disagree, and a quotation that shows no stock should be checked against the vendor ship date before an alternative is proposed.