Contact Us

TPS544B20RVFR

Brand: Texas Instruments
Texas Instruments TPS544B20RVFR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS544B20RVFR — Power Management & Signal Chain | Superb Automation

TPS544B20RVFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS544B20RVFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS544B20RVFR: 18 V Input, 20 A Synchronous Buck With PMBus Telemetry

TPS544B20RVFR is a PMBus enabled synchronous converter with the power stage inside in a 40-pin LQFN body of 40 pins. It converts 4.5 V to 18 V into 0.6 V to 5.5 V at 20 A, reports output voltage, output current and board temperature over PMBus, and shares its pinout with the 30 A TPS544C20.

Order code and package

Ordering stringTPS544B20RVFR, LQFN-40 (RVF), 5 mm by 7 mm, 0.5 mm pitch, single thermal pad
Current20 A for this part, 30 A for the pin compatible TPS544C20 on the same footprint
Input4.5 V to 18 V on both the controller supply and the power stage
Output0.6 V to 5.5 V, regulated against a 600 mV reference
ControlD-CAP or D-CAP2 selectable, differential remote sense at the load
InterfacePMBus 1.1, 3-bit address pins on ADDR0 and ADDR1 for 64 addresses
Temperature-40 C to +125 C junction

Electrical parameters that decide the application

Power stage4.5 mOhm high-side and 2.0 mOhm low-side stacked NexFET, both inside the package
Reference600 mV at 0.5 percent, 594 mV to 606 mV at 125 C
Loop offsetplus or minus 7.5 mV at the 600 mV feedback node, 1.25 percent of the setpoint
Quiescent current10 mA from VDD with the converter not switching, the PMBus engine awake
Thermal resistance27.5 C/W junction to ambient, 4.0 C/W to board, 0.9 C/W to case bottom
Internal regulator6.5 V at 120 mA from BP6, lockout at 3.55 V with 255 mV of hysteresis
Feedback bias50 nA out of the FB pin, so a 10 kohm divider carries 60 uA
Error amplifier130 uS transconductance, loop comparator offset plus or minus 7.5 mV
PMBus functionsVOUT, IOUT and temperature readback, margin and trim, fault response, delays

Points to check before this part goes on a BOM

The 0.5 percent reference is not the DC accuracy of the rail. The loop comparator offset is plus or minus 7.5 mV at the 600 mV feedback node, which is plus or minus 1.25 percent, so the offset is two and a half times the reference term. A PMBus trim command can pull the offset out at one temperature, and the trim code then becomes part of the production test rather than a configuration detail.

Conduction loss can be counted from the two resistances: 20 A through 2.0 mOhm is 0.8 W at full duty, and at 1 V out from 12 V the low-side FET carries 91.7 percent of the period for 0.73 W, while the high-side 4.5 mOhm carries 8.3 percent for 0.15 W. The pair is 0.88 W before switching loss, which on the 27.5 C/W figure is a 24 C rise, so 20 A is a copper and airflow statement.

10 mA of VDD current is 87.6 mAh over a year, which is nothing on a server rail and is fatal to a battery product. The PMBus engine and the housekeeping blocks are awake for that current, so a board that needs microamp standby does not use this part, however convenient the telemetry is.

The 0.6 V floor at 20 A is 12 W, and from a 12 V input the duty is 5 percent, which at 500 kHz is 100 ns of on-time. The efficiency plot on the front page starts at 0.6 V and is the lowest curve on the chart, while 3.3 V at the same current is the top one, so the low end of the output range is where the switching loss share is largest and the inductor choice matters most.

Monotonic start into a pre-biased output is the feature that keeps a rail from pulling down before it comes up. If a 1.0 V rail feeds a load that another source is already holding at 0.4 V, a converter that starts by discharging the output would drag the pre-bias source through its own undervoltage lockout, and the resulting sequence fault is hard to find afterwards.

Two address pins with three bits each give 64 addresses, so a board with eight rails needs sixteen resistors and a single bus. The fault response can be set to restart or to latch, and the trim and margin commands move the setpoint by up to 10 percent, which replaces the two margin pins a conventional controller needs for a production test.

The drivers run from the internal BP6 regulator at 6.5 V, not from the input, so the gate drive is the same at a 5 V input and an 18 V input and the high-side switching loss does not grow with the input rail. BP6 also supplies up to 120 mA to external circuits, which is enough for the PMBus pull-ups and a small housekeeping load, and its 3.55 V lockout is what actually gates start-up.

Where this order code fits

It is used on server and storage rails, Ethernet and optical switch payloads, baseband and instrument supplies, where the rail has to be sequenced, trimmed and watched, and where reading current and temperature over a bus saves a separate monitor on every rail. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Can the 30 A version drop into this footprint? Yes. The TPS544C20 is pin compatible with the same 5 mm by 7 mm body, and the inductor, the copper and the thermal budget are what change.

Does PMBus need another supply? No. BP6 makes 6.5 V at 120 mA from the input, so the bus pull-ups and the housekeeping loads come from the converter itself.

Can the output go below 0.6 V? No. The loop regulates against a 600 mV bandgap, so anything lower needs a different part or an external level shift.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the Strategic Sourcing page sets out the checks that keep a substitute from failing on the bench.