Contact Us

TPS7A5201RPSR

Brand: Texas Instruments
Texas Instruments TPS7A5201RPSR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A5201RPSR — Power Management & Signal Chain | Superb Automation

TPS7A5201RPSR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A5201RPSR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A5201RPSR: 2 A Low-Noise LDO With a Separate Bias Rail

TPS7A5201RPSR is a two amp low dropout regulator with a separate bias supply pin in a 12-pin VQFN body of 12 pins. The bias pin is the reason to use it: with 3 V on VBIAS the input can fall to 1.1 V, so a 0.8 V core runs from a 1.2 V rail that a conventional regulator of this current could not hold.

Order code and package

Ordering stringTPS7A5201RPSR, VQFN-12 (RPS), 2.2 mm by 2.5 mm
Input1.1 V to 6.5 V with VBIAS present, 1.4 V to 6.5 V without
Bias3.0 V to 6.5 V on a dedicated pin
Output0.8 V to 5.15 V at 2 A
Reference0.8 V, output set by an external divider
Controlenable pin rated 6.5 V, open drain power good
Capacitors10 uF input, 22 uF output, 0 nF to 100 nF on NR/SS

Electrical parameters that decide the application

Output accuracy0.5 percent over line, load and temperature
Amplifier offset2.5 mV max
Line regulation0.03 mV/V typ
Load regulation0.012 mV/A typ
UVLO rising, with bias1.02 V to 1.085 V
UVLO rising, without bias1.31 V to 1.39 V
Bias UVLO rising2.83 V to 2.9 V
Output current2 A rated in the recommended range
Thermal resistance46.5 C/W typ, 68.7 C/W max, VQFN-12
Shutdownenable low, output discharged by the internal pulldown

Points to check before this part goes on a BOM

Without a bias rail the UVLO rises at 1.39 V at worst, so a 1.2 V input never starts the part; with 3 V on VBIAS the same input starts at 1.085 V. The bias rail is not a convenience, it is the difference between a 1.2 V rail working and not working, and it has to be present before the input or the device stays in lockout while the upstream converter thinks it has finished.

Two amps from 1.8 V in to 0.8 V out is 2 W in a 2.2 mm by 2.5 mm body, which at 46.5 C/W is a 93 C rise, so the 2 A rating holds only when the input is close to the output. From 3.3 V to 0.8 V at 2 A the loss is 5 W and no package of this size survives it: that case needs a switching stage ahead of the regulator, not a bigger one.

The 0.5 percent accuracy at 0.8 V is 4 mV, and the 2.5 mV of amplifier offset is more than half of that, so the divider tolerance and the offset decide together whether a 0.8 V core sees 0.79 V or 0.81 V. Choosing 0.1 percent resistors buys less than measuring one board and trimming the divider.

Load regulation of 0.012 mV/A is 24 uV at 2 A and line regulation of 0.03 mV/V is 120 uV across a 4 V input change, both far below the accuracy figure, which is why the datasheet leads with temperature and the reference rather than with regulation.

The bias UVLO of 2.83 V to 2.9 V means a 3.3 V rail cannot sag below 2.83 V without dropping the regulator, and a 3.3 V rail at minus 15 percent is 2.805 V, so the margin against the worst case is 25 mV. On boards where the 3.3 V rail is also the load, this is the pair of numbers to check first.

Noise is quoted with 10 nF on NR/SS and 22 uF on the output, and both are load bearing: the NR/SS capacitor sets the reference filtering while the output capacitor sets the loop, so shrinking the output to 10 uF for space makes a different regulator from the one the table describes. A 2 A part with a 10 uF output is a transient and a phase margin away from the datasheet, not a small change.

The enable pin is rated to 6.5 V, the same as the input, so a 5 V logic family drives it directly and a 12 V housekeeping signal does not. Power good is open drain and conditioned with a 100 kOhm pull-up to the input, so that resistor sets both the rise time and the current the pin sinks when the output is outside regulation, and a 1 kOhm pull-up turns the flag into a load on the input.

Where this order code fits

RF synthesisers, data converter supplies and core rails in instrumentation use this part where a 1.2 V or 1.8 V intermediate rail has to feed a lower core voltage with low output noise. A converter front end that already carries a 3.3 V housekeeping rail supplies the bias for free, which is the common case on a data acquisition card, and the 1.1 V input floor is what lets a 1.2 V intermediate rail feed a 0.9 V core without a second switching stage. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

Is the bias pin optional? Optional only if the input stays above 1.4 V. With a 1.1 V to 1.4 V input the bias pin is required, and it must come up before or with the input.

How low can the output go? The reference is 0.8 V, so 0.8 V is the floor. Anything below needs a different reference or a negative rail, and the divider cannot take it lower.

What sets the noise? The internal reference and the error amplifier, filtered by the NR/SS capacitor; the datasheet conditions noise with that capacitor fitted, so removing it changes the figure.

Can two of these share a load? Not without ballast. Each regulates to its own 0.5 percent band, so two outputs in parallel fight unless resistors or a load sharing scheme separate them.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the One Stop RF Supply page sets out the checks that keep a substitute from failing on the bench.