Contact Us

TPS7A8001DRBR

Brand: Texas Instruments
Texas Instruments TPS7A8001DRBR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS7A8001DRBR — Power Management & Signal Chain | Superb Automation

TPS7A8001DRBR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS7A8001DRBR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS7A8001DRBR: 1 A low-noise wide-bandwidth regulator with high ripple rejection

TPS7A8001DRBR is a 1 A linear regulator built for noise-sensitive analogue rails in a VSON body of 8 pins. The adjustable output covers 0.8 V to 6 V, dropout is 170 mV typical at 1 A, output noise is 14 microvolt times the output voltage in RMS from 100 Hz to 100 kHz, and rejection is 63 dB at 1 kHz, 57 dB at 100 kHz and 38 dB at 1 MHz.

Order code and package

Ordering stringTPS7A8001DRBR, DRB package, tape and reel
Package8-pin VSON with thermal pad, 3.00 mm by 3.00 mm
OutputAdjustable from 0.8 V to 6 V with an external divider
Ambient rangeJunction -40 C to 125 C, fully specified across the band
Output capacitor4.7 microfarad ceramic, part of the stability requirement

Electrical parameters that decide the application

Input range2.2 V to 6.5 V, so it runs from a 3.3 V or 5 V rail
Output current1 A
Dropout170 mV typical at 1 A
Accuracy3 percent worst case over load, line, process and temperature
Noise14 microvolt times VOUT RMS, 100 Hz to 100 kHz
Rejection63 dB at 1 kHz, 57 dB at 100 kHz, 38 dB at 1 MHz
ProtectionOvercurrent and overtemperature

Points to check before this part goes on a BOM

Noise scales with the output voltage, so the same part is a different proposition at 1.2 V and at 5 V. At 1.8 V out the figure is 25.2 microvolt RMS, which is 0.9 of a 16-bit least significant bit on a 1.8 V span and 6 percent of one at 12 bits. At 5 V it is 70 microvolt RMS, still under one 16-bit bit on a 5 V span, and that is the point of the part: the noise stays inside a converter bit across the whole output range rather than only at the bottom.

Rejection falls by 25 dB between 1 kHz and 1 MHz, which is the number that matters when the input is a switching rail. A 1 V square wave at 1 MHz becomes 12.6 mV at the output, while the same amplitude at 1 kHz becomes 0.7 mV. A regulator fed from a 2 MHz converter sees the second harmonic at 4 MHz, where rejection is worse again, so the input filter still has a job.

Dropout of 170 mV at 1 A is 0.17 ohm. That puts the minimum input for a 1.8 V output at about 1.97 V and for a 3.3 V output at 3.47 V, which means a 3.3 V rail cannot feed a 3.3 V output at full current. From 5 V to 1.8 V at 1 A the part dissipates 3.2 W in a 3 mm by 3 mm body, so the thermal pad and the copper around it decide the usable current, not the 1 A number.

The 3 percent accuracy is specified over load, line, process and temperature together, which is the only version of the number worth using in a budget. A divider made of 1 percent resistors adds its own error on top, so an adjustable rail built from this part is a 3 percent regulator plus a divider, not a 1 percent one.

A 4.7 microfarad ceramic output capacitor is part of the specification, not a suggestion. The part is stable with ceramic ESR, and the transient response shown in the data sheet assumes that value. Fitting 1 microfarad because the load draws only 200 mA changes the loop margin and the recovery from a load step, and it is the most common substitution error on this family.

The enable pin and the noise-reduction pin are both optional in a copy of the circuit and both change behaviour when removed. Without the noise capacitor the low-frequency noise rises, and without a defined enable the output state at power-up is not guaranteed. On a board that has to come up in a known order, both pins need a defined connection.

The noise reduction pin is the quietest lever on the part and the one most often left unconnected. A small capacitor from that pin to ground filters the reference, which is where most of the low-frequency noise originates, and the effect is largest exactly where a converter cannot help: below a few hundred hertz. Removing the capacitor raises the noise floor at the bottom of the band without changing the 100 kHz figure that the data sheet leads with, so a bench measurement at high frequency will not reveal the mistake.

Where this order code fits

It fits in front of a clock generator, a PLL or VCO supply, an audio converter or a high-speed interface, where the rail has to be quiet at hundreds of kilohertz and the current is under an amp. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Amplifier Cross Reference page.

Questions buyers ask

How much current can I really take from a 5 V input at 1.8 V out? The thermal pad sets it. 3.2 W is the dissipation at 1 A, and the junction rise follows the board's thermal resistance; on a small pad the usable current is well below 1 A. The 1 A rating is an electrical limit, not a thermal promise.

Does the noise figure apply to the fixed versions too? Yes, the noise is quoted as 14 microvolt times the output voltage for the family, so a fixed 1.8 V part and an adjustable one set to 1.8 V are the same figure, provided the same output capacitor and noise capacitor are fitted.

What happens if the output capacitor is smaller than 4.7 microfarad? Stability margin drops and the load-step recovery overshoots. The value is part of the specified operating condition, so a smaller capacitor is an unverified circuit rather than a cost saving.

SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.