UCC27624DR
Product Specifications
UCC27624DR
Texas Instruments — Power Management & Signal Chain
Product Overview
The UCC27624DR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
UCC27624DR: Dual-Channel 5 A Gate Driver With Enable Pins
UCC27624DR is a dual channel low side gate driver with independent enable pins in a 8-pin SOIC body of 8 pins. Each channel sources and sinks 5 A peak, which is enough to move a 100 nC gate in 20 ns, and the two enable pins let a controller hold one channel off while the other runs.
Order code and package
| Ordering string | UCC27624DR, SOIC-8 (D), 4.90 mm by 3.91 mm |
| Package options | SOIC-8 with PowerPAD (DDA), VSSOP-8 (DGN), WSON-8 (DSD), 3.0 mm by 3.0 mm |
| Channels | two, independent, each with its own input and enable |
| Peak output | 5 A source and 5 A sink |
| Inputs | CMOS thresholds, 1.8 V to 2.3 V high, 0.8 V to 1.2 V low |
| Temperature | -40 C to +150 C junction |
Electrical parameters that decide the application
| VDD quiescent current | 300 uA typ, 450 uA max, both channels idle |
| VDD static current | 0.6 mA typ, 1.0 mA max, inputs held |
| VDD operating current | 3.2 mA typ, 3.8 mA max at 1 MHz |
| Disable current | 0.8 mA typ, 1.1 mA max |
| UVLO rising | 3.8 V to 4.4 V |
| UVLO falling | 3.5 V to 4.1 V |
| UVLO hysteresis | 0.3 V |
| Input pulldown | 120 kOhm on each IN pin |
| Enable threshold | 1.8 V to 2.3 V high, 0.8 V to 1.2 V low |
| Thermal resistance | 48.9 C/W to 54.7 C/W, SOIC-8 and SOIC-8 PowerPAD |
Points to check before this part goes on a BOM
The 5 A figure is a peak, and the gate charge decides what it means: 100 nC at 12 V is 1.2 uJ per edge, so at 1 MHz the driver delivers 1.2 W into the gate. Over 48.9 C/W that is a 59 C rise on the driver alone, before the external FET's own dissipation is counted, which is why the PowerPAD version exists in the same family.
The supply lockout releases between 3.8 V and 4.4 V, so a 3.3 V rail cannot run this part at all and a 5 V rail has between 0.6 V and 1.2 V of margin. The 0.3 V of hysteresis is what stops the driver chattering when a bootstrap-fed supply sags under load, and it is small enough that a slow supply ramp still crosses it twice.
A 120 kOhm pulldown on each input means an unconnected IN pin sits low and the channel stays off, so a controller that tri-states its outputs at reset does not turn the FET on. The same resistor draws 27.5 uA at 3.3 V, which is not zero on a standby budget built around a few microamps.
Quiescent current at 450 uA maximum is 3.9 mAh over a year, while the operating figure of 3.8 mA at 1 MHz is 33 Ah, so the difference between a driver that is enabled and one that is switching is four orders of magnitude and the enable pins, not the input signal, are the power control.
Input thresholds are CMOS with 1 V of separation but the enable pins are specified over the same window, so a 2.5 V logic family sits inside the guaranteed high level by 200 mV at worst. A 1.8 V logic family does not reach the 1.8 V minimum with margin and needs a level shift.
Both channels share one VDD pin and one ground, so the 3.8 mA operating current is for the pair and the gate charge current adds on top: two 100 nC gates at 500 kHz is 100 mA of average supply current, thirty times the quiescent figure, and that current comes out of the VDD capacitor between edges. A 1 uF capacitor with a long trace to it turns that into a supply that sags at every switching edge.
The five amp peak is delivered into the gate through the package and the trace, and the trace inductance is in series with it: 10 nH of source path at 5 A in 10 ns is 5 V of drop, which appears at the gate as a slower edge and at the driver as a ground bounce. The shortest possible return from the source of the FET to the ground pin is the difference between the rated edge and the one on the board.
Where this order code fits
Motor drives, synchronous rectification and class D output stages use this part where two gates have to be driven from one small package with independent enables. A half bridge built from two discrete FETs and one driver of this size covers a few hundred watts at 100 kHz, and a two channel motor stage uses both outputs with the enables tied to the controller so either leg can be parked while the other runs. Teams comparing it with a neighbouring part start from our Power Management Cross Reference page, and teams replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.
Questions buyers ask
Are the two channels independent? Yes. Each has its own input and its own enable, and the only shared pins are VDD and ground, so one channel can be held off while the other switches.
Can it drive a high side FET directly? No. Both outputs swing between VDD and ground, so a high side device needs a bootstrap or an isolated supply, which this part does not provide.
What happens below the UVLO threshold? The outputs are held low, so the external FET is off and the load is not driven. The 0.3 V of hysteresis is what keeps that state from oscillating.
Is the SOIC version enough for continuous switching? At 1 MHz and 100 nC the driver alone rises 59 C, so the plain SOIC is a light duty choice and the PowerPAD or the WSON version is the one for continuous operation.
SUPERB holds and sources this line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a part is moving, the BOM Shortage Recovery page sets out the checks that keep a substitute from failing on the bench.