Contact Us

INA4181A4IPWR

Brand: Texas Instruments
Texas Instruments INA4181A4IPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA4181A4IPWR — Power Management & Signal Chain | Superb Automation

INA4181A4IPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA4181A4IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA4181A4IPWR: the gain of two hundred member, bidirectional, on the large reel

INA4181A4IPWR is the gain of two hundred member of the bidirectional four channel current sense family in the fourteen pin TSSOP on the large reel. With a mid supply reference the output moves 1 volt per 5 millivolts of sense voltage, so a 1 milliohm shunt at 5 amps uses a full 1 volt of the swing and the shunt loss stays at 25 milliwatts.

The bandwidth at 200 volts per volt is 105 kilohertz, the lowest of the four, and the offset at a 12 volt common mode is 500 microvolts maximum. Both figures point the same way: this is the member for a direct current path with a small shunt, not for a phase current that reverses at 20 kilohertz.

INA4181A4IPWR as the vendor document publishes it

Channels4
Directionbidirectional, output referred to the reference pin
Referencenormally half the supply
Gain options20, 50, 100 and 200 volts per volt, fixed by an internal network
Common mode range0.2 volts below ground to 26 volts
Supply2.7 to 5.5 volts
Offset at zero volts of common modeplus or minus 25 microvolts typical, plus or minus 150 maximum
Offset at 12 volts of common modeplus or minus 100 microvolts typical, plus or minus 500 maximum
Offset drift0.2 microvolts per degree typical, 1 maximum
Common mode rejection84 decibels minimum, 100 typical at a zero sense voltage
Power supply rejection80 microvolts per volt
Gain error0.1 per cent typical, 1 per cent maximum
Gain error drift20 parts per million per degree
Bandwidth350, 210, 150 and 105 kilohertz for the four gains
Slew rate2 volts per microsecond
Voltage noise40 nanovolts per root hertz
Quiescent current690 microamps typical, 900 maximum at 25 degrees, 1 milliamp over temperature
Temperature rangeminus 40 to plus 125 degrees
Package14 pins, TSSOP body PW
Catalogue codeINA4181A4IPWR
Vendor statusactive
Gain200 volts per volt
Carrierlarge reel, R suffix
Package14 pins, TSSOP body PW

Three hundred and fifty kilohertz, and the gain that takes it away

The four gain options of INA4181A4IPWR carry four bandwidths: 350 kilohertz at 20 volts per volt, 210 at 50, 150 at 100 and 105 at 200, all at a 10 millivolt sense voltage into a 10 picofarad load. The slew rate is 2 volts per microsecond and the voltage noise density is 40 nanovolts per root hertz.

A bidirectional channel on a motor phase sees a current that reverses at the switching frequency, so the small signal bandwidth and the slew rate both matter, and the 200 volts per volt option is the one that gives up the most of both. A 20 kilohertz loop with a 100 millivolt sense signal is comfortable at any of the four gains; a 100 kilohertz loop wants the 20 or 50 option.

Eighty four decibels over the whole common mode window

The common mode rejection of INA4181A4IPWR is 84 decibels minimum and 100 decibels typical, specified from zero to 26 volts of common mode with a zero sense voltage, across the full minus 40 to plus 125 degree range. The power supply rejection is 80 microvolts per volt, and the input bias current is quoted separately for the zero and 12 volt cases.

Eighty four decibels at 26 volts of common mode is 1.6 millivolts of input referred error if the rejection were flat, and the specification is written at the extremes precisely because a bidirectional channel spends its life moving between them. That is the row that decides whether a low side shunt can be replaced by a high side one without losing accuracy.

The offset table read with a mid supply reference

The offset of INA4181A4IPWR is plus or minus 25 microvolts typical and plus or minus 150 microvolts maximum at a common mode of zero volts, and plus or minus 100 microvolts typical with plus or minus 500 microvolts maximum at 12 volts. The drift is 0.2 microvolts per degree typical and 1 microvolt per degree maximum.

With the reference at half supply, the offset appears twice in the transfer function: once as the input offset and once as the error of the reference divider, so the divider tolerance belongs in the same budget. A 1 per cent divider on a 3.3 volt rail is 16.5 millivolts of output shift, which is far larger than the 150 microvolt input offset and is the first thing to fix on a bidirectional channel.

Bidirectional sensing, and the reference pin that makes it work

INA4181A4IPWR is the bidirectional member of the four channel current sense family: the output sits at the reference voltage when the sense voltage is zero, and moves above or below it as current flows in one direction or the other. The reference pin is normally held at half the supply, which puts the zero current point in the middle of the converter range.

The common mode window is the same 0.2 volts below ground to 26 volts, the supply is 2.7 to 5.5 volts, and the four gain options are 20, 50, 100 and 200 volts per volt. The difference from the unidirectional part is not the amplifier but the reference path, and the reference path is what doubles the usable output swing for a given supply.

Six hundred and ninety microamps, and the four channel package

The quiescent current of INA4181A4IPWR is 690 microamps typical and 900 microamps maximum at 25 degrees for all four channels, rising to 1 milliamp maximum over the temperature range. The package is the fourteen pin TSSOP, the same body as the unidirectional quad beside it, and the reel code carries the R suffix.

Four channels at 900 microamps is 225 microamps per channel, which is a quarter of what four separate single channel parts would draw including their own references. That is the reason the quad exists at all in a battery powered instrument, and it is also why the reference divider is normally shared across the four channels rather than built four times.

Where a bidirectional four channel part changes the bill of materials

INA4181A4IPWR belongs in a battery charge and discharge path, where the same shunt carries current both ways; in an H bridge or a solenoid driver, where the direction reverses on every cycle; in a bidirectional converter, where the current sign decides the mode; and in a servo amplifier that regenerates into its supply.

What changes in the bill of materials is the reference: a bidirectional quad needs one stable reference for four channels, and the divider that produces it has to be better than the offset budget or the whole exercise is wasted. The alternative, four unidirectional channels with a level shift each, costs more parts and four more error terms, which is the trade this family exists to avoid.

What the reference pin costs in practice

A reference pin turns a single ended output into a differential one, and the price is that the reference has to be as quiet as the amplifier. A divider from the supply with a 100 nanofarad capacitor is enough for a 1 per cent measurement and is not enough for a 0.1 per cent one, because the supply ripple passes through the divider at its full amplitude.

The second cost is the output swing. With the reference at half supply, each direction gets about 1.6 volts on a 3.3 volt rail instead of 3.2, so a gain that was chosen for a unidirectional channel has to be doubled for the same shunt and the same full scale current. That is the arithmetic to do before the bill of materials is fixed.

The small shunt and the low bandwidth go together, so the application decides before the stock does. Our amplifier cross reference page covers the gain against bandwidth, and the BOM scrubbing page covers the shunt and the reference divider together.

How small can the shunt be at this gain? With a 0.1 milliohm shunt, 5 amps gives 2.5 millivolts of sense and 500 millivolts at the output, which is still usable. Below that the offset of 500 microvolts at a 12 volt common mode is 20 per cent of the signal.

Does the bidirectional part need a different land pattern from the unidirectional one? The pinout is the same and the reference pin is the difference, so the same land pattern serves both and only the connection to the reference changes.