Contact Us

INA4181A3IPWR

Brand: Texas Instruments
Texas Instruments INA4181A3IPWR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA4181A3IPWR — Power Management & Signal Chain | Superb Automation

INA4181A3IPWR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA4181A3IPWR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA4181A3IPWR: quad bidirectional current sense amplifier with 100 V/V gain in a 20-pin TSSOP

INA4181A3IPWR is four independent bidirectional current shunt monitors on one die with a fixed 100 V/V gain in a TSSOP body of 20 pins. The A3 suffix sets 100 V/V, the third of four gain options that share the same die, and the 20-pin TSSOP is the only body that carries all four channels. Each channel senses across its own shunt at common mode voltages from 0.2 V below ground to 26 V while the part runs from a 2.7 V to 5.5 V supply, so the measurement does not follow the logic rail.

Order code and package

Order codeINA4181A3IPWR
Functionquad bidirectional current shunt monitor, voltage output
Gain100 V/V, set by the A3 suffix
PackageTSSOP, 20 pins, the four-channel body
Channelsfour, sharing one supply and one reference per channel
Common mode0.2 V below ground to 26 V, independent of supply
Supply2.7 V to 5.5 V single rail
Gain options20, 50, 100 and 200 V/V across A1 to A4
Bandwidth150 kHz on the A3 gain option with a 10 pF load
Temperature rangeminus 40 to plus 125 C
DatasheetSBOS793 revision H, November 2023, shared with INA181 and INA2181

Electrical parameters that decide the application

Offset voltage150 microvolts maximum at a common mode of 0 V, 500 microvolts maximum at 12 V
Offset drift1 microvolt per C maximum
Gain error1 percent maximum over the full temperature range
Slew rate2 volts per microsecond
Bandwidth by gain350 kHz on A1, 210 kHz on A2, 150 kHz on A3, 105 kHz on A4
Output swingrail to rail within 30 mV of each rail at light load
Reference pinone per channel, sets what zero current reads as
Input biasmatched internal resistor network, no external pair to match
Quiescent current260 microamps maximum for the single channel part, four channels draw more
Isolationnone, the part sits on the measured side of the system

Points to check before this part goes on a BOM

The 100 V/V option is a resolution choice, not a free one. A 10 milliohm shunt at 10 A produces 100 millivolts, which lands as 10 volts at the output and is outside a 5 V rail, so the shunt has to fall to 4 milliohms or the current range has to fall with it.

The bandwidth on this gain option is 150 kHz against 350 kHz on A1. A phase leg switching at 20 kHz still sees the current envelope, but a 150 kHz corner rounds the edges of a short overcurrent spike, so the comparator that protects the bridge should not depend on this channel alone.

Offset is quoted at two common mode voltages and the second number is the one that applies on a live bus. 500 microvolts at 12 V through a 10 milliohm shunt reads as 50 milliamps of current that is not flowing, which is measured at the output as 5 millivolts because the gain multiplies both the signal and the error.

Four channels on one die share a temperature drift, so the ratios between phases stay tight even when the absolute reading moves. That is the reason to use this part rather than four single-channel amplifiers when the board is comparing phases rather than measuring one rail against a meter.

Where this order code fits

Three-phase motor drives and multi-rail battery packs are the boards that order this code, because four channels measure three phases and the return with one reference and one temperature drift. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Lead Time Solutions page.

Questions buyers ask

Does the 26 V common mode cover a 24 V rail? Yes with margin for a nominal 24 V bus, and the part reads down to 0.2 V below ground for a low-side shunt. A 48 V bus is outside the range.

Can one channel be left unused? Yes. The channels are independent apart from the shared supply and ground, and an unused channel only needs its inputs tied to a defined potential.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.