Contact Us

INA333QDGKRQ1

Brand: Texas Instruments
Texas Instruments INA333QDGKRQ1 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA333QDGKRQ1 — Power Management & Signal Chain | Superb Automation

INA333QDGKRQ1

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA333QDGKRQ1 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA333QDGKRQ1: the automotive grade one flow on a 2500 piece reel

INA333QDGKRQ1 is the automotive qualified member of the family in the 8 pin VSSOP on a 2500 piece large reel. It is AEC-Q100 temperature grade 1, minus 40 to plus 125 degrees, functional safety capable with documentation available, and it carries the marking 333Q instead of I333.

The electrical rows are the micro power part's, with the values the automotive document prints: 25 microvolts of maximum offset at a gain of 100 or above, 0.1 microvolts per degree of drift, 50 nanovolts per root hertz and 96 dB minimum of rejection at a gain of 10. The 50 microamps and the 1.8 volt supply floor are unchanged, which is what makes the part usable in a sensor module that has to run from the same rail as the rest of the node.

INA333QDGKRQ1 as the vendor document publishes it

Gain1 plus 100 kilo-ohms divided by the gain resistor
Gain range1 to 1000 V/V
QualificationAEC-Q100 temperature grade 1, minus 40 to plus 125 degrees
Gain error at 10.01 per cent typical, 0.1 per cent maximum
Gain error at 10 and 1000.05 to 0.07 per cent typical, 0.25 per cent maximum
Gain error at 10000.25 per cent typical, 0.5 per cent maximum
Gain drift at 11 ppm per degree typical, 5 ppm per degree maximum
Gain drift above 115 ppm per degree typical, 50 ppm per degree maximum
Offset voltage, automotive25 microvolts maximum at a gain of 100
Offset drift0.1 microvolts per degree typical, 0.5 maximum
Common mode rejection at a gain of 180 dB minimum, 90 dB typical
Common mode rejection at a gain of 10 and above96 dB minimum
Common mode rejection at a gain of 100100 dB minimum, 115 dB typical
Input bias current70 picoamps typical, 200 picoamps maximum
Voltage noise50 nanovolts per root hertz from 10 Hz to 1 kHz
Low frequency noise1 microvolt peak to peak from 0.1 to 10 Hz
Supply range1.8 volts to 5.5 volts
Quiescent current50 microamps
Common mode range0.1 volts inside each rail
Output swing from the rail50 millivolts into 10 kilo-ohms
Stable load capacitance500 picofarads
Input filter150 kilo-ohm series resistors around a 50 kilo-ohm network
Temperature rangeminus 40 to plus 125 degrees
BodyVSSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Vendor statusactive, 2500 piece large reel
Catalogue codeINA333QDGKRQ1
Vendor stringINA333QDGKRQ1
QualificationAEC-Q100 temperature grade 1, minus 40 to plus 125 degrees
Marking333Q
Lead finishNIPDAUAG
Moisture levellevel 2, 260 degrees, one year floor life

The automotive flow and the rows it changes

The automotive code in this family is qualified to AEC-Q100 temperature grade 1, minus 40 to plus 125 degrees, with functional safety documentation available for a safety case. The electrical rows are the industrial part's: 25 microvolts of maximum offset at a gain of 100 or above, 0.1 microvolts per degree of drift, 50 nanovolts per root hertz and 96 dB minimum of rejection at a gain of 10.

What the flow adds is the qualification, the marking and the documentation rather than a tighter grade, so a channel that moves from the industrial code to the automotive one keeps its calibration and its gain resistor. The rows that do move are the rejection minimum, 96 dB on the automotive document against 80 at unity gain on the industrial one, and the drift figure, which the automotive document quotes at a gain of 100 rather than at unity. A purchase order should carry the exact orderable code, because the two documents print different reel sizes for the same body.

Fifty microamps, and the chopper loop behind it

INA333QDGKRQ1 draws 50 microamps of quiescent current and still holds a microvolt class offset, which is only possible because the input stage is auto-corrected rather than trimmed once. The correction loop runs continuously, so the offset that arrives at the converter is the residual of a servo rather than the room temperature sort of an input pair, and the low frequency noise is removed along with it.

That is the whole reason the part exists in a battery instrument. A front end that draws 50 microamps and holds 25 microvolts of offset replaces a precision amplifier plus a calibration step, and it does so on a rail as low as 1.8 volts. The cost of the loop is bandwidth: the same correction that removes the drift also sets a corner, and the part is a slow, quiet amplifier rather than a wide one.

Gain from one to a thousand on one resistor

The gain of INA333QDGKRQ1 is 1 plus 100 kilo-ohms divided by the resistor between the gain pins, so one external resistor covers unity to 1000. At a gain of 1000 that resistor is 100 ohms, at 100 it is 1 kilo-ohm, and at unity the pins are left open.

The internal network is trimmed to 0.01 per cent at unity and 0.07 per cent at a gain of 100, which is better than most external resistors: a 1 per cent resistor gives a 1 per cent channel, and its temperature coefficient adds straight to the 15 ppm per degree of the internal network above unity. The gain drift row of 5 ppm per degree at unity against 50 above unity is the same statement from the other side. A production trim placed in the gain path therefore has to be a low drift part, or the trim becomes the largest error term in the channel.

Twenty five microvolts maximum, and one tenth of a microvolt of drift

The offset of INA333QDGKRQ1 is 10 microvolts typical and 25 microvolts maximum referred to the input at unity gain, with a drift of 0.1 microvolts per degree typical and 0.5 maximum. The output stage carries its own offset, which arrives divided by the gain, and the two drift terms add as uncorrelated errors rather than linearly.

Over the 165 degree window from minus 40 to plus 125 degrees, 0.5 microvolts per degree is 82 microvolts of drift, which is more than the maximum offset itself. That is the arithmetic that decides whether the part is worth its price: a channel that calibrates at 25 degrees and then runs hot sees the total offset grow well past the 25 microvolt headline, and a channel that has no calibration step at all still starts under 25 microvolts, which a 10 millivolt bridge reads as a quarter of a per cent.

Rejection from eighty to one hundred and fifteen decibels

The common mode rejection of INA333QDGKRQ1 is 80 dB minimum and 90 typical at unity gain, rising to 100 dB minimum and 115 typical at a gain of 10 and staying there through 100 and 1000. The input window is 0.1 volts inside each rail, and the inputs carry an RFI filter built from 150 kilo-ohm series resistors with a 50 kilo-ohm network around them.

The rise with gain is the useful shape: a channel that needs rejection buys it by running at a higher gain, which is free on a small sensor and costs bandwidth. The filter inside the package explains why the part is specified with a defined source impedance, and it is also why a high impedance sensor is a different problem: the 150 kilo-ohm series resistors are in the signal path, and their tolerance appears as a gain error on an unbalanced source. A 1 kilo-ohm sensor is unaffected, a 1 megohm one is not.

Fifty nanovolts per root hertz from a part this small

The voltage noise of INA333QDGKRQ1 is 50 nanovolts per root hertz at 10 Hz, 100 Hz and 1 kHz, flat from 100 Hz to 1 kHz, with 1 microvolt peak to peak from 0.1 to 10 Hz. The current noise is 100 femtoamps per root hertz, which against a 10 kilo-ohm source is 1 nanovolt and against a 1 megohm source is 100 nanovolts.

That current noise figure is what makes the part usable on a high impedance sensor at all: an amplifier with a nanoamp of bias current noise would be dominated by the source impedance. The 1 microvolt of low frequency noise has to be read next to the 25 microvolt offset and the 82 microvolts of drift over temperature, because in a DC channel the three add and the noise is usually the smallest of them. The output swing is 50 millivolts from each rail into 10 kilo-ohms, and 500 picofarads of load capacitance is stable.

The automotive flow is bought for the qualification file rather than for a tighter electrical window. Our traceability report page covers the documentation that travels with the reel, and the BOM scrubbing page covers the qualified code against the bill of materials.

Is the Q1 part a different die? No. The flow adds qualification, grade testing and the marking; the architecture, the 50 microamps and the gain law are shared with the industrial code.

Why does the rejection read 96 dB here and 80 dB there? The industrial document quotes the unity gain row and the automotive one quotes a gain of 10, and the rejection rises with gain.