Contact Us

INA321E-2K5

Brand: Texas Instruments
Texas Instruments INA321E-2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA321E-2K5 — Power Management & Signal Chain | Superb Automation

INA321E-2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA321E-2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA321E-2K5: the E grade on a 2500 piece reel, printed with a slash by the vendor

INA321E-2K5 is the E grade of the micropower CMOS instrumentation amplifier in the 8 pin MSOP, on a 2500 piece large reel. It draws 40 microamps per channel and under 1 microamp in shutdown, runs from 2.7 to 5.5 volts, and holds 200 microvolts typical and 500 maximum of offset with 94 dB of typical rejection and 0.02 per cent of gain error at a gain of 5.

The code needs one reading note: the vendor prints this row as INA321E/2K5 with a slash, and our catalogue code uses a hyphen in the same place. Both refer to the same 2500 piece large reel at moisture level 2, and the marking on the part is 2321EA. A purchase order that carries the hyphen and a vendor document that carries the slash describe one part, not two.

INA321E-2K5 as the vendor document publishes it

Quiescent current40 microamps per channel
Shutdown currentunder 1 microamp
Offset voltage200 microvolts typical, 500 microvolts maximum
Offset drift2 microvolts per degree
Input bias current10 picoamps
Common mode rejection90 dB minimum, 94 dB typical
Gain equation5 plus 5 multiplied by the ratio of the two external resistors
Gain error at 50.02 per cent
Gain drift2 ppm per degree
Bandwidth at 3 dB500 kHz at a gain of 5
Slew rate0.8 volts per microsecond
Output swing to the positive rail20 millivolts
Supply range2.7 volts to 5.5 volts, single or bipolar
Common mode range at 5 volts0.55 volts to 3.8 volts
Common mode range at 2.7 volts0.35 volts to 1.5 volts
Input impedance10 to the 13 ohm in parallel with 3 picofarads
BodyMSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Temperature rangeminus 55 to plus 125 degrees
Vendor statusactive, 2500 piece large reel
Catalogue codeINA321E-2K5
Vendor stringINA321E/2K5, printed with a slash
GradeE, 500 microvolts maximum offset
Marking2321EA
Moisture levellevel 2, 260 degrees, one year floor life

The gain lives outside the package

The gain of INA321E-2K5 is 5 plus 5 times the ratio of two external resistors, so the minimum gain is 5 and the maximum is about 1000 depending on the resistor values. Everything above 5 comes from the resistor pair, and that is the part of the channel the data sheet does not trim.

Two consequences follow. The first is that the gain accuracy at 5 is specified at 0.02 per cent while the gain at 100 is only as good as the resistors: a pair of 1 per cent resistors gives a 1 per cent channel, and a pair of 0.1 per cent resistors gives 0.1 per cent. The second is that the resistor network is a place to put a filter, a multiplexer or a calibration trim, because the two nodes are brought out. A channel that has to trim gain in production can put a potentiometer in the divider, and the drift of that potentiometer becomes the drift of the gain.

Forty microamps per channel, and under one in shutdown

INA321E-2K5 draws 40 microamps per channel and under 1 microamp with the shutdown pin pulled low, from a supply of 2.7 to 5.5 volts. The shutdown feature is not a gimmick on this part: a battery instrument that wakes once a second and reads a bridge for 2 milliseconds spends 0.2 per cent of its life in measurement, and a front end that draws 40 microamps while asleep empties a coin cell in weeks.

The return from shutdown takes microseconds, which is fast enough to be part of a scan rather than a power cycle. That matters for a multiplexed channel where several sensors share one amplifier: the part is powered for the channel that is being read and shut down for the rest, and the settling time of the amplifier is now part of the channel budget along with the multiplexer and the converter.

The letter after the part number widens the window

The INA321 is sold in two grades and the difference is entirely in the specification columns. The E grade holds 200 microvolts typical and 500 microvolts maximum of offset, 90 dB minimum of common mode rejection and 0.02 per cent of gain error at a gain of 5. The EA grade holds 1 millivolt maximum of offset, 80 dB minimum of rejection and 0.07 per cent of gain error, for a lower price.

That is the whole of the choice, and it is worth stating plainly because the two codes look alike on a purchase order. A channel that measures a 10 millivolt bridge signal has 1 millivolt of offset on the EA grade, which is 10 per cent of full scale before any gain is applied; the E grade has 0.5 millivolt, or 5 per cent, and neither is a precision channel without a calibration step. A channel that only has to detect a threshold rather than to measure a value can use either.

Ten picoamps of bias against a high impedance source

The input bias current of INA321E-2K5 is 10 picoamps, and the input impedance is 10 to the 13 ohms in parallel with 3 picofarads. A bridge of 350 ohms does not care about either figure. A pH electrode, a photodiode or a 10 megohm thermistor does: 10 picoamps into 10 megohms is 100 microvolts, which is the same order as the offset of the EA grade.

That is why the bias current and the offset have to be read together. A high impedance source converts bias current into an offset that is indistinguishable from the amplifier's own, and the conversion is linear in the source resistance. The same arithmetic applies to the bias current path: an input that has no DC return charges the 3 picofarads until the amplifier leaves its common mode range, and the symptom is a channel that works on the bench and drifts on the board.

Five hundred kilohertz at a gain of five

The bandwidth of INA321E-2K5 is 500 kHz at a gain of 5, with a slew rate of 0.8 volts per microsecond and an output that swings to within 20 millivolts of the positive rail. For a micropower part that is a wide front end, and it is what makes the family usable in front of a fast converter rather than only in a slow logger.

The bandwidth falls as the gain rises, so a gain of 100 channel is a few tens of kilohertz wide, and the output stage has to drive the sampling capacitor of the converter as well as the feedback network. The 20 millivolt swing to the rail is the row that decides the top of the range: a 12 bit converter with a 4.096 volt reference has a 1 millivolt least significant bit, so 20 millivolts of headroom is 20 codes that cannot be used, and a channel that needs the top of the range has to run the amplifier from a rail above the reference.

Where a micropower instrumentation amplifier fits

INA321E-2K5 fits a portable medical front end for ECG or EMG, a bridge or thermistor channel in a handheld instrument, a 4 to 20 milliamp loop that has to run on the loop current, and a battery powered field meter that reads a differential line. The 40 microamps, the shutdown pin and the 500 kHz bandwidth at a gain of 5 are the three rows that make those applications possible.

It stops at four things. The minimum gain is 5, so a unity gain buffer is a different part. The offset is in the hundreds of microvolts on the E grade and a millivolt on the EA grade, so a precision DC channel needs a chopper stabilised amplifier instead. The supply floor is 2.7 volts, which rules out a single cell. And the part is specified to minus 55 to plus 125 degrees but with the offset and rejection rows that belong to a low cost amplifier, so an instrumentation channel that has to hold 0.01 per cent over temperature belongs elsewhere. Our amplifier cross reference page lists the alternatives by front end type.

The grade and the carrier are the two fields to check on this row, and the slash is the third. Our BOM scrubbing page covers the code check against the bill of materials, and the amplifier cross reference page covers the parts either side of this one.

Is this the same part as INA321E/2K5? Yes. The vendor prints a slash and our catalogue prints a hyphen; the reel, the grade and the marking are the same.

What is the difference from the EA grade? The offset window, 500 microvolts against 1 millivolt, the rejection, 90 dB minimum against 80, and the gain error, 0.02 per cent against 0.07.