Contact Us

INA317IDGKT

Brand: Texas Instruments
Texas Instruments INA317IDGKT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA317IDGKT — Power Management & Signal Chain | Superb Automation

INA317IDGKT

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA317IDGKT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA317IDGKT: the fifty microamp instrumentation amplifier on a 250 piece reel

INA317IDGKT is the micropower instrumentation amplifier in the 8 pin VSSOP of 3.00 by 3.00 millimetres, on a 250 piece small reel. It draws 50 microamps typical and 75 maximum, runs from 1.8 to 5.5 volts, and sets its gain with one resistor from unity to 1000 as 1 plus 100 kilo-ohms divided by that resistor.

The 250 piece reel is the carrier that suits a pilot run and a rework bench rather than a line: the same die in the 2500 piece reel is INA317IDGKR, and both carry the marking I317. The rows that decide the channel are the 10 microvolts typical and 75 maximum of offset, the 0.3 microvolts per degree of drift and the 50 nanovolts per root hertz of noise, which is a quiet front end for a part that draws this little.

INA317IDGKT as the vendor document publishes it

Supply range1.8 volts to 5.5 volts single, plus or minus 0.9 to plus or minus 2.75 dual
Quiescent current50 microamps typical, 75 maximum, 80 maximum over temperature
Offset voltage at unity gain10 microvolts typical, 75 microvolts maximum
Offset drift0.3 microvolts per degree typical
Input bias current70 picoamps typical, 200 picoamps maximum
Input offset current50 picoamps
Common mode rejection at unity gain90 dB typical, 80 minimum
Common mode rejection at 10 and above110 to 115 dB typical, 100 minimum
Power supply rejection0.5 microvolts per volt typical
Voltage noise density50 nanovolts per root hertz at 10 Hz, 100 Hz and 1 kHz
Current noise density100 femtoamps per root hertz at 10 Hz
Gain equation1 plus 100 kohm divided by the gain resistor
Gain range1 to 1000
Gain error at unity gain0.01 per cent typical, 0.1 per cent maximum
Gain error at 1000.07 per cent typical, 0.25 per cent maximum
Gain error at 10000.25 per cent typical, 0.5 per cent maximum
Gain drift above unity15 ppm per degree typical, 50 maximum
Bandwidth150 kHz at unity, 35 kHz at 10, 3.5 kHz at 100, 350 Hz at 1000
Slew rate0.16 volts per microsecond at unity gain
Settling to 0.01 per cent50 microseconds at unity gain, 400 at a gain of 100
Overload recovery60 microseconds from a 50 per cent overdrive
Output swing from the rail50 millivolts maximum into 10 kohm
Stable load capacitance500 picofarads
Reference input impedance300 kohm
BodyVSSOP, 8 pin, DGK, 3.00 by 3.00 millimetres
Temperature rangeminus 40 to plus 125 degrees
Vendor statusactive, 250 piece small reel
Catalogue codeINA317IDGKT
Vendor stringINA317IDGKT
MarkingI317
Moisture levellevel 2, 260 degrees, one year floor life
Carrier notethe 2500 piece reel is INA317IDGKR

One resistor sets the gain from one to a thousand

The gain of INA317IDGKT is 1 plus 100 kilo-ohms divided by the resistor between the two gain pins, so a single external resistor covers the whole range from unity to 1000. At a gain of 1000 that resistor is 100 ohms, at 100 it is 1 kilo-ohm, and at unity the two pins are left open, which makes the part usable as a buffer without a gain network at all.

The resistor is also the largest error term at high gain. The internal resistors are trimmed to 0.01 per cent at unity and 0.07 per cent at 100, but an external resistor of 1 per cent tolerance adds its error directly to the gain, and its temperature coefficient adds directly to the gain drift. A gain of 1000 built with a 100 ohm resistor of 0.1 per cent and 25 ppm per degree is therefore a 0.1 per cent channel, not a 0.07 per cent one. The 3.5 kHz bandwidth at that gain and the 400 microsecond settling to 0.01 per cent are the other half of the same choice: high gain is available and it is slow.

Fifty microamps, and what that buys

INA317IDGKT draws 50 microamps typical and 75 maximum, or 80 over the full temperature range, from a supply as low as 1.8 volts. That is one twentieth of a conventional instrumentation amplifier and it is the reason the part exists: a 4 to 20 milliamp loop transmitter has a budget of about 3 milliamps for the whole circuit, and a front end that takes 50 microamps leaves room for the converter, the reference and the regulator.

The comparison that matters is not against a precision laboratory amplifier but against the rest of the channel. A 16 bit converter at 100 samples per second draws more than the amplifier in most channels, and a shunt reference draws more again. At that point the 50 microamps stop being the constraint and the offset become one, which is why the same part also carries 75 microvolts of maximum offset and 0.3 microvolts per degree of drift: the micropower budget was met without giving up the DC rows.

Seventy five microvolts, and where the offset comes from

The offset of INA317IDGKT is 10 microvolts typical and 75 microvolts maximum referred to the input at unity gain, with a drift of 0.3 microvolts per degree typical. The output stage carries its own offset, which appears divided by the gain, so the highest gain is also the most accurate per volt of input: a 1 millivolt output offset at a gain of 1000 is 1 microvolt at the input.

That division is why the part is specified at unity gain in the first place. A channel that runs at a gain of 100 has an input referred offset made almost entirely of the input stage, and the output stage term falls below the resolution of the measurement. The drift of 0.3 microvolts per degree over 165 degrees is about 50 microvolts, so a channel that calibrates once at room temperature and runs to 85 degrees sees the offset double; a channel that calibrates in production at the operating temperature does not.

Where a micropower instrumentation amplifier earns its place

INA317IDGKT suits a battery instrument that measures a bridge or an RTD, a 4 to 20 milliamp transmitter that has to run on the loop current, a portable medical front end where the supply is a coin cell or a small lithium cell, and a pressure or load cell channel that is sampled slowly and has to hold its offset between calibrations.

It stops at four things. The supply floor is 1.8 volts, so a single alkaline cell at 1.5 volts needs a boost converter before the amplifier. The bandwidth at a gain of 1000 is 350 Hz, which rules out vibration and acoustic channels. There is no shutdown pin, so the 50 microamps are drawn for as long as the rail is up. And the input common mode stops 0.1 volts inside the rails, so a high side shunt on a 24 volt bus needs a divider or a different front end. Our amplifier cross reference page covers the parts that trade quiescent current for bandwidth or for a wider common mode window.

Rail to rail output from a 1.8 volt supply

INA317IDGKT runs from 1.8 to 5.5 volts single ended, or from plus and minus 0.9 to plus and minus 2.75 volts, and the output swings to within 50 millivolts of either rail into a 10 kilo-ohm load. The input common mode range stops 0.1 volts inside each rail, which is what makes a single supply bridge or a ground referenced thermocouple usable without a negative rail.

The inputs also carry an RFI filter: two 150 ohm series resistors and a differential capacitor at the pins, which is the network that keeps a cellular handset or a switching supply from being rectified by the input stage and appearing as a DC shift. That filter costs about 300 ohms of source impedance tolerance and adds a pole, and the pole is the reason the part is specified with a defined source impedance. A high impedance sensor that needs the full 10 to the 13 ohm input impedance has to be treated as a different problem: the filter is inside the package and cannot be removed.

Bandwidth that falls with gain, and why that is intended

The 3 dB bandwidth of INA317IDGKT is 150 kHz at unity gain, 35 kHz at 10, 3.5 kHz at 100 and 350 Hz at 1000, and the slew rate is 0.16 volts per microsecond at unity. The product is roughly constant, which is the signature of a single pole compensation, and it means the settling time grows with gain in a predictable way: 50 microseconds to 0.01 per cent at unity and 400 microseconds at a gain of 100.

For a sensor channel that is the right trade. A thermocouple or an RTD at 10 samples per second does not need 150 kHz, and the same 50 microamps that buys the low quiescent current buys a slow amplifier. Where the trade goes wrong is a multiplexed channel: a 16 channel scan that settles for 400 microseconds per channel spends 6.4 milliseconds in settling alone, and the converter's own throughput is wasted. That channel needs the gain switched by a resistor network rather than by the amplifier, or a faster part with a larger supply current.

Two hundred and fifty pieces is a prototype quantity, and the reel size is the only difference from the 2500 piece code. Our amplifier cross reference page covers the instrumentation amplifiers either side of this one, and the vendor consolidation page covers buying both reels from one line.

What resistor sets a gain of 100? 1 kilo-ohm, from 100 kilo-ohms divided by 100. A gain of 1000 needs 100 ohms.

Is there a shutdown pin? No. The 50 microamps are drawn whenever the rail is up, which is why the part suits a loop powered transmitter and not a sleeping instrument.