Contact Us

INA317IDGKR

Brand: Texas Instruments
Texas Instruments INA317IDGKR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA317IDGKR — Power Management & Signal Chain | Superb Automation

INA317IDGKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA317IDGKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA317IDGKR: zero drift instrumentation amplifier in a 8-pin VSSOP

INA317IDGKR is a zero drift instrumentation amplifier with a single resistor gain setting in a VSSOP body of 8 pins. One external resistor sets any gain from 1 to 1000 with the standard 1 plus 100 kiloohm over RG relation. The part runs from 1.8 V to 5.5 V, draws 50 microamps, and holds 75 microvolts of offset and 0.3 microvolts per C of drift at gains of 100 and above, which is where a bridge or a thermocouple sits.

Order code and package

Order codeINA317IDGKR
Functionzero drift instrumentation amplifier
Gain1 to 1000, set by one external resistor
Gain equationG equals 1 plus 100 kiloohms divided by RG
PackageVSSOP, 8 pins
Supply1.8 V to 5.5 V single rail
Input range0.1 V inside each rail
Output range0.05 V inside each rail
Quiescent current50 microamps
Temperature rangeminus 40 to plus 125 C
Inputradio frequency filtered
DatasheetSBOS948 revision A

Electrical parameters that decide the application

Offset voltage75 microvolts maximum at gains of 100 and above
Offset drift0.3 microvolts per C at gains of 100 and above
Noise50 nanovolts per root hertz at gains of 100 and above
Common mode rejection100 dB minimum at gains of 10 and above
Input bias current200 picoamps maximum
Supply current50 microamps typical
Bandwidthset by the gain and the internal compensation
Gain errorset by the external resistor tolerance, the die is trimmed for the equation
Output stagerail to rail within 50 millivolts
Zero driftinternal correction removes the low frequency offset term

Points to check before this part goes on a BOM

The offset and drift figures are quoted at gains of 100 and above, not at unity. A board that runs this part at gain 2 has to read the gain dependent rows, because the input referred offset of a zero drift stage grows as the gain falls.

The gain accuracy is the external resistor. The die holds the 100 kiloohm ratio, and a 1 percent resistor gives a 1 percent gain error no matter how well the amplifier is trimmed.

Fifty microamps of supply current at 1.8 V is 90 microwatts, which is the reason this part exists in battery products. A chopper amplifier with comparable offset usually draws ten times that.

Zero drift removes the offset term but not the thermocouple effects at the input. Two junctions of dissimilar metal across a 5 microvolt per C pair will swamp a 0.3 microvolt per C amplifier, so the board has to keep the inputs isothermal.

The input and output ranges stop short of the rails by 100 and 50 millivolts. A single supply bridge with its common mode at ground cannot use the full span, and the reference has to be lifted above ground for the output to have room.

Radio frequency filtering at the input matters more than the offset on a cable run. A demodulated mobile handset near the amplifier can shift the reading by more than the whole offset budget, and the internal filter only helps if the source impedance is low.

Where this order code fits

Battery powered sensor nodes and 4 to 20 milliamp loops are the boards that use it, because a 1.8 V rail and 50 microamps leave room for the converter behind it. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Does the price of the external resistor matter? Yes for gain accuracy. The die is trimmed to the 100 kiloohm relation and the resistor sets the actual gain, so a 0.1 percent resistor and a 1 percent resistor give different gain errors on the same part.

Can it run from a single 3.3 V rail with a ground referenced sensor? It can run from 3.3 V, but the output needs 50 millivolts of headroom and the input 100 millivolts, so a ground referenced bridge needs the reference pin lifted to keep the signal in range.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.