Contact Us

INA282AIDR

Brand: Texas Instruments
Texas Instruments INA282AIDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA282AIDR — Power Management & Signal Chain | Superb Automation

INA282AIDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA282AIDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA282AIDR: 50 V/V bidirectional current sense amplifier with 140 dB rejection

INA282AIDR is a bidirectional current shunt monitor with a fixed 50 V/V gain in a SOIC body of 8 pins. This is the 50 V/V member of a five part family that runs from 50 to 1000 V/V, with a common mode range from 14 V below ground to 80 V and 140 dB of rejection. The gain is fixed on the die, so the family number picks the full scale and the order code picks the package.

Order code and package

Order codeINA282AIDR
Functionbidirectional current shunt monitor
Gain50 V/V, fixed on the die
PackageSOIC, 8 pins
Common mode14 V below ground to 80 V
Supply2.7 V to 18 V
Channelsone
Family gains50 V/V INA282, 100 INA286, 200 INA283, 500 INA284, 1000 INA285
Temperature rangeminus 40 to plus 125 C
Referenceoutput offset set by a REF pin for bidirectional sensing
DatasheetSBOS485 revision D

Electrical parameters that decide the application

Offset voltage20 microvolts
Offset drift0.3 microvolts per C
Gain error1.4 percent maximum
Gain drift0.005 percent per C maximum
Common mode rejection140 dB
Quiescent current900 microamps maximum
Bandwidthset by the fixed gain stage, low compared with a PWM rejecting part
Outputvoltage output centred by the REF pin
Input biasmatched on both inputs to keep the common mode term small
Settlingslow enough that the sampling instant matters on a switching load

Points to check before this part goes on a BOM

The gain is fixed on the die, so the family number is a full scale decision made at the board stage. Moving from 50 to 200 V/V means a different part number and a different shunt, not a resistor change.

140 dB of rejection is a DC and low frequency figure. This part does not carry the enhanced PWM rejection of the INA240 line, so a phase leg switching at 20 kHz with fast edges will see common mode transients this device was not specified against.

Offset drift of 0.3 microvolts per C is 37 microvolts across the full range, nearly twice the 20 microvolt initial offset. A production calibration at room temperature does not remove that term.

The supply range tops out at 18 V, which rules out direct operation from a 24 V rail. A board that has only the motor bus available needs a local regulator for this part, and that regulator is part of the measurement error if it moves.

Gain error of 1.4 percent is wide compared with the instrumentation amplifiers in this catalogue, and it is the price of the wide common mode front end. A project that needs 0.2 percent has to calibrate or choose a different family.

900 microamps of quiescent current in a SOIC body is modest, but four channels on a drive add 3.6 milliamps to the low voltage rail, and the shunt wiring has to be kept clear of the switching node for the rejection figure to mean anything.

Where this order code fits

Motor drives, welding equipment and battery systems that need a fixed gain and a wide common mode are the boards that specify it, often as a lower cost alternative to a PWM rejecting part. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Component Obsolescence Management page.

Questions buyers ask

Why does the family cover 50 to 1000 V/V in separate part numbers? The gain is trimmed on the die, so each ratio is its own order code; there is no external gain resistor and no way to change the ratio on a built board.

Is this part suitable for a phase node on a 48 V inverter? It handles the 80 V common mode, but it has no enhanced PWM rejection, so the switching transient error has to be handled by the sampling scheme or by a part from the INA240 line.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.