Contact Us

INA240A4D

Brand: Texas Instruments
Texas Instruments INA240A4D is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA240A4D — Power Management & Signal Chain | Superb Automation

INA240A4D

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA240A4D from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA240A4D: the 200 V/V gain in the SOIC, and the row the addendum closes

INA240A4D is the 200 V/V option in the 8 pin SOIC, the highest gain of the four, and the addendum prints it Obsolete with a dash in the quantity column. The gain is for the smallest shunt drops: 10 millivolts of shunt at 200 V/V is 2 volts, so a 0.2 milliohm shunt at 50 amps is inside the converter range.

The active row at this gain is INA240A4DR on a 2500 piece reel, which the same addendum prints as active with the lead finish on call. The electrical rows are unchanged across the pair, including 25 microvolts of maximum offset and 250 nanovolts per degree of drift, so the move is a carrier change and nothing else. The settling time at this gain is 9.8 microseconds rather than 9.6, which is the only row that differs from the lowest gain option.

INA240A4D as the vendor document publishes it

Gain200 V/V fixed
Gain error0.05 per cent typical, 0.20 per cent maximum
Gain drift2.5 ppm per degree maximum
Nonlinearity0.5 ppm typical, 2.5 ppm maximum
Offset voltage5 microvolts typical, 25 microvolts maximum, referred to the input
Offset drift250 nanovolts per degree maximum
Common mode rejection, DC120 dB minimum, 132 dB typical
Common mode rejection at 50 kHz93 dB
Power supply rejection1 microvolt per volt typical, 10 maximum
Input bias current90 microamps
Common mode rangeminus 4 volts to plus 80 volts, independent of the supply
Supply range2.7 volts to 5.5 volts
Quiescent current1.8 milliamps typical, 2.4 milliamps maximum
Bandwidth at 3 dB400 kHz at every gain
Bandwidth at 2 per cent distortion100 kHz at every gain
Slew rate2 volts per microsecond
Settling to 0.5 per cent9.6 microseconds at the 20 V/V gain, 9.8 at the 200 V/V gain
Voltage noise density40 nanovolts per root hertz
Reference divider accuracy0.01 per cent typical, 0.1 per cent maximum
Reference input range0 volts to the supply rail
Swing to the positive rail50 millivolts typical, 200 maximum into 10 kohm
Swing to ground1 millivolt typical, 10 maximum
Stable load capacitance1 nanofarad
Temperature rangeminus 40 to plus 125 degrees
Vendor statusobsolete in the package addendum, no quantity printed
Catalogue codeINA240A4D
Vendor stringINA240A4D, obsolete; INA240A4DR is the active row
BodySOIC, D, eight pin, 4.90 by 3.91 millimetres
MarkingI240A4

Two bodies, eleven order codes and the rows the addendum marks obsolete

INA240A4D comes in an 8 pin TSSOP of 3.00 by 4.40 millimetres and an 8 pin SOIC of 4.90 by 3.91 millimetres, both at moisture level 2 with a 260 degree peak and a one year floor life. The four gains are available in both bodies, so the body is a thermal and a footprint decision rather than a functional one: the TSSOP spreads heat better on a small board, the SOIC is easier to inspect and to rework by hand.

The addendum read for this page carries obsolete rows that are easy to order by accident. The tube codes INA240A2PW, INA240A3PW, INA240A4PW and the SOIC tube INA240A4D are printed Obsolete while the reel codes of the same gain and body are active, and INA240A2PWR is printed active with a dash in the quantity column instead of a reel size. A line that needs a few pieces for a pilot usually reaches for the tube, and that is exactly the row that is closed. Read the status column before the quantity column.

Twenty five microvolts against a ten millivolt full scale

The offset of INA240A4D is 5 microvolts typical and 25 microvolts maximum referred to the input, with a drift of 250 nanovolts per degree maximum. Against a 10 millivolt shunt drop, which is the smallest full scale the family is specified for, the maximum offset is 0.25 per cent of full scale and the typical part is 0.05 per cent.

The drift row deserves the same arithmetic. At 250 nanovolts per degree over the 165 degree window from minus 40 to plus 125, the drift term is about 41 microvolts, which is larger than the maximum room temperature offset. A single point calibration at 25 degrees therefore buys less than the drift spec, and a channel that has to hold 0.5 per cent over temperature either runs a smaller temperature window, calibrates at the operating temperature, or uses the zero drift architecture for what it is: a guarantee that the offset does not wander, not a guarantee that it is zero.

Four hundred kilohertz on all four gains

The bandwidth of INA240A4D is 400 kHz at 3 dB and 100 kHz at 2 per cent distortion, and neither figure changes with the gain option. That is unusual for a current sense amplifier, where the gain stage normally trades bandwidth for gain, and it comes from the difference amplifier topology: the four gains are set by internal resistors on one die, so the 20 V/V and the 200 V/V option have the same pole.

The number that matters in a motor drive is the settling time, 9.6 microseconds at the 20 V/V gain and 9.8 at the 200 V/V gain to 0.5 per cent of the final value. A 20 kHz switching frequency leaves a 25 microsecond on-time at 50 per cent duty, and 9.6 microseconds is 38 per cent of it, so the sample has to be taken in the later part of the window. At 100 kHz switching the on-time is 5 microseconds and the output is still moving when the sample is taken, so the reading is low by whatever the output has not yet reached. A drive that samples at that speed needs a shorter settling time, not a faster converter.

Minus four volts of common mode, and why a solenoid needs it

The input of INA240A4D is specified from 4 volts below ground to 80 volts above it, and the window does not move with the supply rail. The negative end is there for the flyback period of a solenoid or a relay: when the switch opens, the low side of the coil swings below ground and the shunt with it, and a monitor that stops at zero volts loses the reading for exactly the part of the cycle where the current is decaying.

The positive end covers a 48 volt telecom bus and a 72 volt battery pack with margin, again from a 3.3 or 5 volt rail, because the input divider is internal and the common mode window is independent of the supply. What the window does not cover is a bus that rings above 80 volts: above the limit the part is not specified, and the current that flows through the protection network becomes the error. A bus with a transient above 80 volts needs a series resistor on both inputs or a different part, and the decision belongs in the requirements rather than in a note on the drawing set.

Where a PWM rejecting shunt monitor earns its place, and where it stops

INA240A4D suits four kinds of channel: the phase current of a three phase motor drive, where the common mode steps at every switching edge; a solenoid or valve driver, where the current decays through a diode and the low side goes below ground; a telecom rectifier or a 48 volt power shelf, where the bus sits above the logic supply; and an actuator or pressure regulator loop that closes on current rather than on position.

It stops at four things. There is no digital output, so a converter and its reference are part of the channel. There is no isolation, so a mains referenced shunt needs an isolator behind the amplifier. The quiescent current of 1.8 milliamps typical rules out a battery instrument that sleeps. And the 10 millivolt full scale floor sets the shunt: at 10 millivolts and 25 microvolts of maximum offset, a shunt that develops less than 10 millivolts at the working current does not get more accurate by being larger, it gets slower and hotter. Our amplifier cross reference page covers the parts that trade one of those four for something else.

What enhanced PWM rejection removes from the output

A motor phase carries a common mode step of tens of volts in a few hundred nanoseconds when the bridge switches, and a current sense amplifier sees it on both inputs at once. The rejection at 50 kHz on INA240A4D is 93 dB, so a 60 volt step is attenuated to about 1.3 millivolts at the input, which at the 50 V/V gain is 65 millivolts of output movement rather than a recovery tail that lasts for milliseconds.

That figure is the one to compare between parts, because the DC rejection of 132 dB says nothing about a step. Amplifiers that quote only a DC number can still take tens of microseconds to recover, and the recovery lands inside the sampling window of the converter. The trade is bandwidth against rejection: 400 kHz is wide enough that the output follows a real current step, and the rejection network is narrow enough that the switching edge does not pass. A channel that filters the output to 10 kHz throws away most of the bandwidth and gains nothing on the edge, because the edge is already rejected at the input.

At this gain the shunt is small and the offset term is the limit, so the choice of row is a carrier question. Our obsolete part cross reference hub covers the active reel code, and the amplifier cross reference page covers the gains below this one.

Is the highest gain also the most accurate? It is the most sensitive: 25 microvolts of offset at 200 V/V is 5 millivolts of output, so the offset is amplified with the signal.

Which row replaces this one? INA240A4DR on a 2500 piece reel; the D row without the R is closed.