Contact Us

INA217AIDWT

Brand: Texas Instruments
Texas Instruments INA217AIDWT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA217AIDWT — Power Management & Signal Chain | Superb Automation

INA217AIDWT

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA217AIDWT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA217AIDWT: the same amplifier on a two hundred and fifty piece reel

INA217AIDWT is the same audio instrumentation amplifier in the same wide body sixteen pin package on a 250 piece small reel. The T suffix is the carrier and nothing else changes: 1.3 nanovolts per root hertz, 3.4 MHz at unity and 800 kHz at a gain of 100, 15 volts per microsecond, 10 milliamps of supply current and the same plus or minus 4.5 to 18 volt window.

Two hundred and fifty pieces is a prototype and first article quantity, and for an audio channel that is the right size, because the gain resistor and the source impedance have to be characterised in the actual circuit. The moisture level is 3 with a 168 hour floor life on both carriers, so the small reel buys inventory relief rather than handling relief.

INA217AIDWT as the vendor document publishes it

Gain equation1 plus 10 kilo-ohms divided by the gain resistor
Gain range1 to 10000 V/V
Gain error at unity0.1 per cent typical, 0.25 maximum
Gain error at 100.2 per cent typical, 0.7 maximum
Gain error at 1000.2 per cent typical
Gain error at 10000.5 per cent typical
Gain drift at unity3 ppm per degree typical, 10 maximum
Gain drift above 1040 ppm per degree typical, 100 maximum
Nonlinearity0.0003 per cent of full scale at unity, 0.0006 at a gain of 100
Voltage noise1.3 nanovolts per root hertz at 1 kHz, 1.5 at 100 Hz, 3.5 at 10 Hz
Current noise0.8 picoamps per root hertz at 1 kHz
Output stage noise90 nanovolts per root hertz at 1 kHz
Distortion plus noise0.004 per cent at 1 kHz and a gain of 100
Offset50 plus 2000 over G microvolts typical, 250 plus 5000 over G maximum
Offset drift1 plus 20 over G microvolts per degree typical, 3 plus 200 over G maximum
Input bias current2 microamps typical, 12 maximum
Input offset current0.5 microamps typical, 1 maximum
Input impedance60 megohms in parallel with 2 picofarads
Common mode rejection at unity70 dB minimum, 80 typical
Common mode rejection at 100100 dB minimum, 116 typical
Bandwidth3.4 MHz at unity, 800 kHz at a gain of 100
Slew rate15 volts per microsecond
Settling to 0.01 per cent3.5 microseconds on a 10 volt step at a gain of 100
Output swingwithin 2 volts of each rail minimum into 2 kohm
Supply rangeplus or minus 4.5 to plus or minus 18 volts
Quiescent current10 milliamps typical, 12 maximum
Temperature rangeminus 40 to plus 85 degrees specified
Vendor statusactive, 250 piece small reel
Catalogue codeINA217AIDWT
Vendor stringINA217AIDWT
BodySOIC, DW, sixteen pin wide body, 10.30 by 7.50 millimetres
Moisture levellevel 3, 260 degrees, 168 hour floor life

A gain law of one plus ten kilo-ohms over the gain resistor

Gain on INA217AIDWT is set by one external resistor and the law is 1 plus 10 kilo-ohms divided by RG, so 10 kilo-ohms gives 2, 1.1 kilo-ohms gives 10, 111 ohms gives 100 and 11 ohms gives 1000. The range is quoted as 1 to 10000 V/V, and the gain error rows are published per gain: 0.1 per cent typical and 0.25 maximum at unity, 0.2 typical and 0.7 maximum at 10, 0.2 typical at 100 and 0.5 typical at 1000.

The 10 kilo-ohm numerator is the one difference from the INA163, which uses 6 kilo-ohms for the same job, so a resistor chosen for one part does not give the same gain on the other. Gain accuracy is a function of the external resistor, as the document states in its own footnote, and the drift row follows the same split: 3 parts per million per degree at unity and 40 at any gain above 10, both typical, because at unity the external resistor is out of the path and above it the resistor's drift enters the gain directly.

Offset written as a function of the gain

The offset row of INA217AIDWT is 50 plus 2000 divided by G microvolts typical and 250 plus 5000 divided by G maximum, which at unity is 2.05 and 5.25 millivolts, at 100 is 70 and 300 microvolts, and at 1000 is 52 and 255 microvolts. Drift follows the same shape, 1 plus 20 over G microvolts per degree typical and 3 plus 200 over G maximum.

The input stage's offset is referred to the input and appears in full at every gain; the output stage's offset is divided by the gain, so the two terms trade places as the gain rises. Reading the row correctly decides what a given channel can be used for. At unity the part has 5.25 millivolts of maximum offset and 23 microvolts per degree of drift, which is a monitoring grade channel. At 100 the same part has 300 microvolts and 5 microvolts per degree, which is a measurement grade channel. Nothing about the part changed; only where the error is referred to.

Plus or minus 4.5 to 18 volts, and the wide body to carry it

The supply window of INA217AIDWT is plus or minus 4.5 to plus or minus 18 volts, rated at plus or minus 15, and the quiescent current is 10 milliamps typical and 12 maximum. The output reaches within 2 volts of each rail at minimum and 1.8 typical into a 2 kilo-ohm load, so on plus or minus 15 volts the usable swing is about plus or minus 13 volts, and the short circuit current is 60 milliamps into the common point.

Ten milliamps at 30 volts total is 300 milliwatts, which in a sixteen pin wide body is a modest rise, and the part is stable into 1000 picofarads so a metre of screened cable needs no series resistor. Both order codes on this page are the same wide SOIC body and differ only in carrier: the R suffix is 2000 pieces on a large reel and the T suffix is 250 pieces on a small reel, both at moisture level 3 with a 168 hour floor life after the bag is opened.

One point three nanovolts per root hertz at a gain of 100

INA217AIDWT is a current feedback instrumentation amplifier built for low level audio. Voltage noise is 1.3 nanovolts per root hertz at 1 kHz, 1.5 at 100 Hz and 3.5 at 10 Hz, current noise is 0.8 picoamps per root hertz, and the output stage contributes 90 nanovolts per root hertz.

Against a 200 ohm source, which is what a moving coil cartridge or a low impedance microphone presents, the source resistance generates 1.8 nanovolts per root hertz at room temperature, so the amplifier's 1.3 is below the source's own noise and the pair is close to the best a bipolar input can do. On a 10 kohm source the resistance generates 12.8 nanovolts and the amplifier's figure no longer matters. That is why the family's application list starts with microphones and moving coil transducers, and why a 10 kohm bridge is the wrong home for this part however quiet it looks on paper.

Microphone preamp, moving coil and differential receiver

INA217AIDWT covers three jobs that are the same circuit: a microphone preamp where the source is 150 to 200 ohms and the signal is millivolts, a moving coil cartridge amplifier where the source is a few ohms and the signal is smaller still, and a differential receiver at the end of a balanced cable where the job is to reject what the cable picked up.

All three want the same two rows, a low voltage noise into a low source impedance and a common mode rejection of 100 dB minimum at a gain of 100, which is 116 typical. The limits are the same in all three as well. The bias current of 2 microamps typical and 12 maximum rules out a high impedance source, the supply floor of plus or minus 4.5 volts rules out a single rail, and the 60 milliamp output is a short circuit rating rather than a working current. Our amplifier cross reference page sets it against the quieter INA163 and the lower current members, and the medical device components page covers the patient connected channels where the bias current and the isolation both matter.

Distortion cancellation in the output stage

Total harmonic distortion plus noise on INA217AIDWT is 0.004 per cent at 1 kHz and a gain of 100, and the document attributes part of that to a cancellation circuit in the output stage rather than to loop gain alone. Nonlinearity is 0.0003 per cent of full scale at unity and 0.0006 at a gain of 100.

For a microphone preamp the figure that matters is the one at the gain the channel actually runs. A preamp at 100 for a 200 ohm source produces a few millivolts of signal at the input and a volt at the output, so the output stage is working at a small fraction of its swing and the distortion mechanism is second order rather than clipping. That is why the cancellation matters here and would not on a line stage driven near its rails, and it is also why a channel that needs the last tenth of a per cent should keep the output below a few volts peak to peak rather than run the part at its limit.

A small reel is a pilot quantity and the second purchase is the decision. Our safety stock planning page covers that arithmetic, and the lead time page covers the case where the small carrier is not on the shelf.

Does the T suffix change the electrical rows? No. It is the same die in the same wide body on a 250 piece reel instead of 2000.

Can the part run from a single 5 volt rail? No. The window starts at plus or minus 4.5 volts, and the output needs about 2 volts of headroom on each side of the swing.