INA2132U
Product Specifications
INA2132U
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA2132U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA2132U: the plain grade of the dual unity gain difference amplifier in a fifty piece tube
INA2132U is the dual unity gain difference amplifier in the fourteen pin SOIC, supplied in a fifty piece tube, with 75 microvolts typical and 250 microvolts maximum of offset at plus and minus 15 volts. The gain is fixed at 1 by an internal resistor network, the inputs accept a common mode that reaches twice the rails, and each amplifier draws 160 microamps.
The tube is the carrier for a first build, and the same grade is published on a 2500 piece reel as INA2132U/2K5. The part is the low power member of the difference amplifier pair in this catalogue: 300 kilohertz of bandwidth and 0.1 volts per microsecond of slew, against 1.5 megahertz and 5 volts per microsecond on the faster member, for a fifth of the supply current.
INA2132U as the vendor document publishes it
| Channels | 2 |
| Gain | 1 V/V, fixed by the internal network |
| Supply | plus or minus 1.35 to plus or minus 18 volts, single 2.7 to 36 volts |
| Quiescent current | 160 microamps typical, 185 maximum per amplifier |
| Offset, plain code | 75 microvolts typical, 250 maximum at plus and minus 15 volts |
| Offset, A code | 150 microvolts typical, 500 maximum at plus and minus 15 volts |
| Offset on a 5 volt single rail | 150 typical with 500 maximum plain, 750 maximum A code |
| Offset drift, plain / A | 1 typical with 5 maximum / 10 maximum microvolts per degree |
| Rejection, plain / A | 80 minimum, 90 typical / 74 minimum, 90 typical decibels |
| Gain error, plain / A | 0.01 typical with 0.05 maximum / 0.1 maximum per cent |
| Input impedance | 80 kilo-ohms differential, 40 kilo-ohms common mode, 20 per cent absolute |
| Output noise | 65 nanovolts per root hertz at 1 kilohertz |
| Bandwidth and slew | 300 kilohertz, 0.1 volts per microsecond |
| Settling time | 85 microseconds to 0.1 per cent on a 10 volt step |
| Output drive | plus or minus 12 milliamps, stable into 10 nanofarads |
| Temperature range | minus 40 to plus 85 degrees specified, minus 55 to plus 125 operating |
| Vendor status | active, fifty piece tube |
| Catalogue code | INA2132U |
| Carrier | tube of 50 |
| Lead finish | printed as a call to the vendor on this row |
| Moisture level | level 3, 260 degrees, 168 hour floor life |
Unity gain, built on a ratio matched resistor network
INA2132U is a dual difference amplifier with a fixed gain of 1, built around a thin film resistor network that is ratio matched inside the package. The network is what sets the gain and the rejection at the same time, which is why the gain error is 0.01 per cent typical and the common mode rejection is 90 dB typical without any external trimming.
The absolute value of the resistors is a different matter: the document prints the differential input impedance as 80 kilo-ohms and the common mode impedance as 40 kilo-ohms, with a tolerance of 20 per cent on the absolute value against a ratio match that is far tighter. A source below 1 kilo-ohm is unaffected. A source of 100 kilo-ohms forms a divider with the 80 kilo-ohm input and loses 55 per cent of its signal before the amplifier sees it, and no amount of ratio matching recovers that.
Two hundred and fifty microvolts on the plain grade, five hundred on the A grade
At plus and minus 15 volts the offset of INA2132U is 75 microvolts typical and 250 microvolts maximum on the plain code, against 150 typical and 500 maximum on the A code. The drift is 1 microvolt per degree typical with 5 maximum on the plain code and 10 on the A code, and the power supply rejection is 5 microvolts per volt typical against 30 maximum.
The single supply table is looser than the split supply one and quotes 150 microvolts typical with 500 maximum on the plain code and 750 on the A code at 5 volts. That is the table a 5 volt system has to read, because the input stage is biased at mid rail there and the common mode sits at 2.5 volts. A channel that calibrates at 25 degrees still has to carry the 2 microvolts per degree drift over the 125 degree operating window, which is 250 microvolts of movement on its own.
A common mode window that reaches outside the rails
The inputs of INA2132U are divided by two ahead of the amplifier, so the common mode window is wider than the supply. The document prints the window as 2 times the negative rail minus the reference voltage at the bottom and 2 times the positive rail minus 1 volt, minus the reference, at the top. On a plus and minus 15 volt rail that is roughly plus and minus 28 volts of common mode, which is why the rejection row is quoted from minus 30 to plus 28 volts.
That is the property that makes the part useful for a high side sense. A 24 volt bus can be monitored by a part running from a 15 volt rail, as long as the divider keeps the input inside the window. The rejection is 80 dB minimum and 90 dB typical on the plain code, 74 and 90 on the A code, and the channel separation is 0.04 microvolts per volt, which is 88 dB, so two channels on two phases do not talk to each other.
One hundred and sixty microamps, three hundred kilohertz, ten nanofarads of load
INA2132U draws 160 microamps typical and 185 maximum per amplifier, which is a tenth of what an audio line receiver of the same era draws, and it still reaches 300 kilohertz of bandwidth with a slew rate of 0.1 volts per microsecond and a settling time of 85 microseconds to 0.1 per cent on a 10 volt step.
The output stage is the unusual row: it is stable into 10 nanofarads of load, which is far beyond the 500 picofarads that most parts of this class accept, and it sources and sinks 12 milliamps continuously. That makes the part able to drive a cable or a passive filter directly rather than through a buffer. The slow slew rate is the price: 0.1 volts per microsecond is 10 microseconds for a 1 volt step, which is fine for a sensor channel and too slow for a video signal.
The same part on a single supply from 2.7 to 36 volts
In single supply operation INA2132U runs from 2.7 to 36 volts, with the reference pin tied to mid supply so that the output sits at half rail with no input. The offset table changes with that connection and is quoted separately, and the common mode window becomes minus 2.5 to plus 5.5 volts on a 5 volt rail, which is the input range of a difference amplifier whose inputs are divided by two and then referenced to the reference pin.
The reference pin has to be driven from a low impedance. A divider of two 10 kilo-ohm resistors adds 5 kilo-ohms to the reference path and the amplifier's own 40 kilo-ohm network then sees a source that moves with the output, which turns into gain error and into a slow settling tail. A 1 microfarad capacitor at the pin, or an op amp buffer, keeps the reference where the offset table expects it.
Where a unity gain difference amplifier belongs
INA2132U belongs where a differential signal has to become a single ended one with no gain: a 4 to 20 milliamp receiver, a current shunt on a low side, a ground loop breaker between two chassis, a bridge that feeds a converter with its own programmable gain, and a differential current receiver in a motor drive. The wide common mode window and the 12 milliamp output are the two rows that decide most of those cases.
It does not belong in front of a high impedance sensor, because the 80 kilo-ohm differential input loads it. It does not belong where gain is needed, because the gain is fixed at 1. It does not belong in a precision DC channel that has to hold microvolts, because 250 microvolts of offset with 5 microvolts per degree is a calibration problem on every board. Our amplifier cross reference page covers the graded difference amplifiers either side of this one, and the BOM scrubbing page covers the reference divider against the bill of materials.
The reference connection and the source impedance decide the accuracy of this part. Our amplifier cross reference page covers the faster member of the pair, and the BOM scrubbing page covers the reference divider against the bill of materials.
Does the part really accept a common mode above its own rail? Yes. The inputs are divided by two ahead of the amplifier, so the window is roughly twice each rail minus the reference.
What limits a high impedance source? The 80 kilo-ohm differential input. A 100 kilo-ohm source loses more than half its signal before the amplifier sees it.