Contact Us

INA2126UA2K5

Brand: Texas Instruments
Texas Instruments INA2126UA2K5 is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA2126UA2K5 — Power Management & Signal Chain | Superb Automation

INA2126UA2K5

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA2126UA2K5 from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA2126UA2K5: the A grade on a 2500 piece reel, the only reel carrier the family publishes

INA2126UA2K5 is the A grade of the dual micro power instrumentation amplifier in the sixteen pin SOIC on a 2500 piece large reel, the orderable code INA2126UA/2K5 on the vendor addendum. It is the only reel carrier published for this body in either grade, and it is moisture level 3 with a 168 hour floor life rather than the level 2 of the tube.

The reel code is what a production line buys. The electrical rows are the A grade's: 500 microvolts maximum of offset, 74 dB minimum of rejection, 50 nanoamps of bias current maximum, 175 microamps per channel and a gain of 5 to 10000 on one resistor. A board that moves from the tube to the reel keeps its calibration and changes only its floor life and its handling window.

INA2126UA2K5 as the vendor document publishes it

Channels2
Gain5 to 10000 V/V, 5 + 80 kilo-ohms / RG
Supplyplus or minus 1.35 to plus or minus 18 volts
Quiescent current175 microamps typical, 200 maximum per channel
Offset, plain code100 microvolts typical, 250 maximum
Offset, A code150 microvolts typical, 500 maximum
Offset drift, plain / A0.5 typical with 3 maximum / 5 maximum microvolts per degree
Input bias current, plain / A10 typical with 25 maximum / 50 maximum nanoamps
Rejection, plain / A80 minimum, 94 typical / 74 minimum, 83 typical decibels
Voltage noise35 nanovolts per root hertz at 1 kilohertz, 24 on the TID flow
Bandwidth200 kilohertz at a gain of 5, 250 on the TID flow
Slew rate0.4 volts per microsecond
Settling time160 microseconds to 0.01 per cent at a gain of 100
Channel separation130 decibels at a gain of 5
Temperature rangeminus 40 to plus 85 degrees
Package16 pins, SOIC body D
Vendor statusactive, 2500 piece large reel
Catalogue codeINA2126UA2K5
Vendor stringINA2126UA/2K5
Carrierlarge reel of 2500
Moisture levellevel 3, 260 degrees, 168 hour floor life

Two channels that draw one hundred and seventy five microamps each

INA2126UA2K5 is the dual member of a two op amp instrumentation amplifier family that runs from a total supply of 2.7 to 36 volts, which is plus and minus 1.35 to plus and minus 18 volts on a split rail. Each channel draws 175 microamps typical and 200 microamps maximum, so a two channel front end costs 400 microamps on the supply and leaves the rest of a battery instrument to its converter and its radio.

The low current is bought against bandwidth rather than against accuracy: the offset of the family is in the hundreds of microvolts and the gain error is a fraction of a per cent, which is a different trade from the chopper parts that draw 50 microamps and hold 25 microvolts. A channel that samples a bridge once a second does not need bandwidth, and this is the family that spends its current budget on the second channel instead.

Two hundred and fifty microvolts, and the grade letter that widens it

The offset sort is where the two grade letters separate, and the direction surprises buyers. The plain codes, INA2126U and INA2126E, are printed at 100 microvolts typical and 250 microvolts maximum at 25 degrees, with a drift of 0.5 microvolts per degree typical and 3 maximum. The A codes, INA2126UA and INA2126EA, are printed at 150 microvolts typical and 500 microvolts maximum, with a drift of 5 microvolts per degree maximum.

The same split runs through the rest of the table. Common mode rejection is 80 dB minimum and 94 dB typical on the plain codes against 74 dB minimum and 83 dB typical on the A codes, and the input bias current maximum is 25 nanoamps against 50. On this family the A suffix marks the wider of the two sorts rather than a premium bin, so a purchase order that treats A as better will pay for a looser part.

Two hundred kilohertz at a gain of five, and one hundred and sixty microseconds to settle

The 3 dB bandwidth of INA2126UA2K5 is 200 kilohertz at a gain of 5 on one flow and 250 kilohertz on the other, with a slew rate of 0.4 volts per microsecond and a settling time of 160 microseconds to 0.01 per cent at a gain of 100. The output swings to within 0.9 volts of the positive rail and 0.95 volts of the negative one, and the part is stable into 1000 picofarads of load.

Those rows set the scan rate of a multiplexed front end. At a gain of 100 the part needs 160 microseconds to settle, so eight channels scanned in sequence cost 1.3 milliseconds before any conversion time is added, which is a 750 sample per second ceiling for the whole bank. A channel that needs more has to raise the gain later in the chain or accept fewer channels, and a channel that runs at a gain of 5 has the full 200 kilohertz to work with.

Gain from five to ten thousand on one resistor

The gain law of INA2126UA2K5 is 5 plus 80 kilo-ohms divided by the resistor between the two gain pins, so a single resistor covers 5 to 10000. With the pins left open the gain is exactly 5, which is the value the part is trimmed at; a 20 kilo-ohm resistor gives 9, a 2 kilo-ohm resistor gives 45 and a 100 ohm resistor gives 805.

The floor of 5 is deliberate. A two op amp instrumentation amplifier needs gain to keep its input stage inside the common mode window, and the data sheet states that a minimum circuit gain of 5 is what permits an adequate DC common mode range and enough bandwidth. A channel that needs unity gain, a buffer or a gain of 2 is not this part, and forcing it lower moves the input stage out of its linear region before the output reaches the rail.

Thirty five nanovolts, and the second chip flow

The voltage noise of INA2126UA2K5 is 35 nanovolts per root hertz at 1 kHz and at 100 Hz on the SHE flow, and 24 nanovolts per root hertz on the TID flow, with 0.7 microvolts peak to peak from 0.1 to 10 Hz on the first and 0.5 on the second. The current noise is 160 femtoamps per root hertz, which against a 10 kilo-ohm source is under 2 nanovolts and against a 1 megaohm source is 160 nanovolts.

The document states that TI qualifies more than one fabrication flow for the part and that the difference is labelled by chip site origin. The two columns are not a sorting option: a board is built from whichever flow is in the reel. That is why the data sheet recommends a budget that covers both, and why the offset and the bias current rows carry the same split. A low impedance source sees the noise difference as 3 nanovolts and does not care about the current column at all.

Where a two op amp front end fits, and the four rows that rule it out

INA2126UA2K5 fits a bridge or an RTD channel in a handheld instrument, a thermocouple front end with cold junction compensation, a 4 to 20 milliamp receiver with a sense resistor, and any two channel data acquisition board that has to run from a split rail of plus and minus 5 or plus and minus 15 volts. The 130 dB of channel separation at a gain of 5 also makes it usable for two sensors that share a return.

It stops at four rows. The supply floor of 2.7 volts total rules out a single lithium cell without a boost. The gain floor of 5 rules out a buffer. The common mode window of plus and minus 11.25 volts on a 15 volt rail rules out a high side sense on a 48 volt bus. And an offset class of hundreds of microvolts rules out a shunt or a load cell that has to resolve tens of microvolts without a calibration step. Our amplifier cross reference page covers the zero drift parts for that last case, and the BOM scrubbing page covers the gain resistor against the bill of materials.

A reel is a moisture level 3 part, so the floor life is part of the purchase. Our traceability report page covers what travels with the reel, and the BOM scrubbing page covers the handling level against the bill of materials.

Is the reel code the same die as the tube? Yes, same body and same electrical rows, and the A grade is the only sort published on the reel.

What changes in handling? The tube is level 2 with a one year floor life and the reel is level 3 with 168 hours, so the reflow schedule and the bake rule are different.