Contact Us

INA191A2IYFDR

Brand: Texas Instruments
Texas Instruments INA191A2IYFDR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA191A2IYFDR — Power Management & Signal Chain | Superb Automation

INA191A2IYFDR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA191A2IYFDR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA191A2IYFDR: 50 V/V picoamp current sense amplifier in a wafer level package

INA191A2IYFDR is an ultra small current shunt monitor with 100 picoamp input bias current in a DSBGA body of 6 pins. The 0.895 square millimetre wafer level body is the point of this order code: it fits under a camera module or beside a battery connector where a SOT-23 cannot go. Inside it senses from 0.2 V below ground to 40 V, draws 43 microamps, drops to 100 nanoamps in shutdown, and the A2 suffix fixes the gain at 50 V/V.

Order code and package

Order codeINA191A2IYFDR
Functionbidirectional current shunt monitor with enable
Gain50 V/V, set by the A2 suffix
PackageDSBGA, 6 balls, 1.17 mm by 0.765 mm
Package area0.895 square millimetres
Common mode0.2 V below ground to 40 V
Supply1.7 V to 5.5 V
Input bias current100 picoamps typical
Channelsone
Temperature rangeminus 40 to plus 125 C
Gain optionsA1 25, A2 50, A3 100, A4 200, A5 500 V/V
DatasheetSLYS020 revision C, August 2021

Electrical parameters that decide the application

Offset voltage12 microvolts maximum
Offset drift0.13 microvolts per C maximum
Gain error0.25 percent maximum on A2 to A5 devices
Gain drift7 ppm per C maximum
Quiescent current43 microamps at 25 C
Shutdown current100 nanoamps maximum
Bandwidth37 kHz on the A2 gain option
Slew rate0.3 volts per microsecond
Noise75 nanovolts per root hertz referred to the input
REF pinnot present on this single channel body

Points to check before this part goes on a BOM

The 100 picoamp bias current is what makes a 10 kiloohm shunt usable. A 1 nanoamp leakage into a cheaper amplifier would be 10 microvolts across that shunt, which is most of this part's 12 microvolt offset budget before the signal arrives.

The wafer level body has no REF pin on the single channel version. A board that needs bidirectional sensing has to take the dual channel INA2191 in the 12 ball body, because the offset cannot be moved on this one.

43 microamps of quiescent current is below most sleep currents of the host, which changes the power budget arithmetic. A product that samples once a second can leave the amplifier enabled and spend less than the wake up cost of the microcontroller.

Gain error of 0.25 percent on this option is wider than the offset suggests, and it is a fixed term. A one point calibration in production removes it, which is why this grade is often calibrated while the cost optimised line is not.

At 50 V/V, a 40 amp load through a 1 milliohm shunt produces 2 volts at the output, so the 5.5 V supply headroom is never the limit; the shunt dissipation is. The same load through a 0.5 milliohm shunt keeps the output in range and halves the loss.

The ball grid body needs the same thermal care as any chip scale part: the balls are the only path to the board, and a shunt placed under the package heats the die through the same path that carries the signal.

Where this order code fits

Wearables, phone battery paths and any board where the sense amplifier is the last part that has to fit are the usual reasons this order code comes up. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Pin to Pin Cross Reference page.

Questions buyers ask

Can it sense current in both directions without a REF pin? Not on this body. The single channel part has no REF input, so the output is referenced to ground; the dual channel INA2191 in the 12 ball package carries the REF pin.

Is the 6 ball body reworkable in a service centre? It is a chip scale package with no compliant leads, so rework needs a reball or a replacement board; the 8 pin SOT-23 option exists for boards that expect repairs.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Incoming Inspection Plan page sets out the checks that keep a substitute from failing on the bench.