TPS54140ADGQR
Product Specifications
TPS54140ADGQR
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54140ADGQR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54140A 42 V 1.5 A step down converter with a tighter enable window
The TPS54140ADGQR is a 42 V, 1.5 A step down regulator with the high side switch in the package, in the 10 pin VSON body with an exposed pad or the MSOP body of the same footprint. It is the middle member of a family that runs from 42 V to 60 V, and its job is to take a 12 V or 24 V industrial bus down to 5 V or 3.3 V at a current that a small board actually needs. The switch is 200 milliohm, the reference is 0.8 V, and the frequency can be set anywhere from 100 kHz to 2.5 MHz or locked to an external clock.
The A suffix is the whole reason to name this part rather than the plain TPS54140. The enable window is 1.11 V to 1.36 V instead of 0.9 V to 1.55 V, so the pin behaves as a real undervoltage lockout rather than a loose switch. On a 24 V bus that dips when a contactor closes, that window decides whether the rail holds or resets the logic behind it.
Key parameters taken from the SLVSB55C document
| Input range | 3.5 V to 42 V operating, with an internal UVLO at 2.5 V |
| Output current | 1.5 A, with the high side switch on resistance at 200 milliohm typical and 410 milliohm maximum at 12 V in, and 300 milliohm at 3.5 V in |
| Switching frequency | 100 kHz to 2.5 MHz set by the RT/CLK resistor, synchronisable to an external clock |
| Reference | 0.8 V, 0.792 V to 0.808 V at 25 degrees and 0.784 V to 0.816 V over minus 40 to plus 150 degrees |
| Quiescent current | 116 microamp typical and 136 microamp maximum while not switching at 12 V in, 1.3 microamp typical and 4 microamp maximum in shutdown |
| Enable pin | 1.11 V to 1.36 V window, 3.8 microamp of input current, and a hysteresis current of 1.91 to 3.99 microamp for the divider |
| Power good | Open drain output that releases when the output is inside 94 to 107 per cent of nominal |
| Protection | Cycle by cycle current limit, frequency foldback and thermal shutdown during an overload |
| Compensation | Current mode, 97 microsiemens of error amplifier transconductance, 2700 kHz of error amplifier bandwidth, 6 A per V of COMP to switch current gain |
| Package | 10 pin VSON 3 mm by 3 mm and 10 pin MSOP, both with an exposed pad |
Frequency foldback and why it protects the switch
When the output is shorted, a current mode converter cannot reduce the on time below its minimum, and the inductor current keeps climbing until the switch fails. The TPS54140A handles this by folding the switching frequency down as the feedback voltage falls, which lengthens each cycle and gives the current limit time to act. In practice a shorted output produces a low frequency hiccup rather than a dead part, and the audible result is a tick rather than silence. The same mechanism is why an overload recovery looks like a soft start: the frequency has to climb back before the loop resumes normal operation.
Setting the lockout from the enable pin
The enable pin has an internal pull up current source, so two resistors set the start voltage, and the hysteresis current widens the band between start and stop. A 24 V bus that has to start at 18 V and hold down to 15 V is a divider plus the hysteresis current, and the vendor's equation accounts for both. Because the A suffix window is tighter, the same divider gives a more predictable start point than it would on the plain part, and the spread over temperature is smaller.
Soft start, tracking and sequencing
The SS/TR pin charges a capacitor with a fixed current, and the voltage on that pin overrides the internal reference, so the output follows it up. The same pin can be driven from a divider on another rail, which makes this supply track a higher voltage during start up, a common requirement when a 1.2 V core has to come up after a 3.3 V rail has reached regulation. A small capacitor is enough for a slow start, and the pin can also be used to hold the output off from a supervisor.
Where the part fits and what to watch on a quote
Typical sockets are 24 V industrial I/O modules, 12 V aftermarket automotive accessories, and point of load rails in instrumentation where 1.5 A is enough. The 42 V rating covers a 24 V bus with a wide transient but not a 48 V telecom rail, which is the reason the 60 V family member exists.
Two details matter commercially. The VSON and MSOP bodies share the die but not the thermal path, so a board qualified with one and built with the other will run at a different temperature. And the A suffix is a different orderable part from the plain suffix, so a quote that names only the base number can deliver a part with the wider enable window and still look correct on paper. Our desk names the suffix and the body on every line, and shows the family alternatives on power management cross reference.
Frequently asked questions
Can the part run at 2.5 MHz at full load. The frequency is available, but the minimum on time and the switching loss set the practical limit. At 2.5 MHz and 24 V in, the on time for a 3.3 V output is short enough that the part starts to skip pulses at light load, and the switching loss at 1.5 A is significant. A rail that needs small size usually settles between 500 kHz and 1 MHz.
What happens if the boot capacitor is missing. The high side switch cannot turn on, and the output stays at zero while the part continues to switch the low side. The symptom is a dead rail with a live controller, which is why the boot capacitor is the first thing to check. See one stop BOM sourcing for the passive list that goes with this part.