TPS54060MDGQTEP
Product Specifications
TPS54060MDGQTEP
Texas Instruments — Power Management & Signal Chain
Product Overview
The TPS54060MDGQTEP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
TPS54060M-EP enhanced product 60 V 0.5 A converter for minus 55 to 125 degrees
The TPS54060MDGQTEP is the enhanced product version of the TPS54060 family. The silicon is the same 60 V, 0.5 A regulator with an integrated 200 milliohm high side switch, but the qualification is different: minus 55 to plus 125 degrees ambient and minus 55 to plus 150 degrees junction, against minus 40 as the bottom of the standard grade. The part is offered in the 10 pin DGQ body only, and the electrical table is specified over the full enhanced window rather than over the commercial one, which is why several limits are looser than on the standard part.
Enhanced products exist for programs that cannot use a commercial grade but do not need a full space level screening flow. The datasheet states the limits over the wider range, and the rest of the flow, the moisture level and the reel, follows the standard package. For a board that has already been qualified around the TPS54060, the enhanced part usually drops in with the same external components, and the differences show up in the reference window and the enable window rather than in the pinout.
Key parameters taken from the SLVSCF8 document
| Input range | 3.5 V to 60 V operating, 65 V absolute maximum, with the internal UVLO at 2.5 V |
| Temperature | Minus 55 to plus 125 degrees ambient, minus 55 to plus 150 degrees junction, storage minus 65 to plus 150 degrees |
| Reference | 0.8 V, 0.792 V to 0.808 V at 25 degrees, and 0.78 V to 0.821 V over the full enhanced range |
| Switch resistance | 300 milliohm at 3.5 V in, 200 milliohm typical and 465 milliohm maximum at 12 V in, the maximum being wider than the 410 milliohm of the standard grade |
| Quiescent current | 116 microamp typical and 150 microamp maximum while not switching, 1.3 microamp typical and 8 microamp maximum in shutdown |
| Enable pin | 0.9 V to 1.6 V window, 3.8 microamp of hysteresis current, floating pin means enabled |
| Switching frequency | 100 kHz to 2.5 MHz set by the RT/CLK resistor, synchronisable to an external clock |
| Thermal | 62.5 degrees per watt on a standard board and 57 degrees per watt on a custom board, in the 10 pin DGQ body |
| ESD | 1000 V human body model and 500 V charged device model, the body model being half the standard grade figure |
| Output current | 0.5 A continuous |
The four numbers that differ from the standard grade
Anyone comparing the two datasheets should look at four rows. The reference window widens from 0.784 V to 0.816 V on the standard part to 0.78 V to 0.821 V here, which matters on a rail that is trimmed at the bottom of its tolerance. The switch resistance maximum at 12 V in rises from 410 to 465 milliohm, which is a 13 per cent increase in conduction loss at the same current. The shutdown current maximum rises from 4 to 8 microamp. And the human body model ESD rating falls from 2000 V to 1000 V, which is still above the 500 V that the JEDEC note treats as safe for a standard handling area, but is not the same number.
None of those four changes the external circuit. They change the margins in the qualification report, and they are the reason a board cannot simply be signed off by copying the standard part's numbers into the enhanced part's test plan.
Enable, lockout and start up over the wide range
The enable pin still has the internal pull up current source, so a divider from VIN sets the lockout and the 3.8 microamp hysteresis current sets the width. At minus 55 degrees the divider current changes very little, since the current source is specified over the range, but the threshold window is wider than the A suffix of the standard grade, and a board that sits close to the bottom of the window at room temperature should be checked at both ends. The soft start is a capacitor on SS/TR, charged with 2 microamp, and the same capacitor provides tracking if the pin is driven from another rail.
Thermal behaviour in a cold soak and a hot soak
The thermal figure is a steady state number and does not describe the cold start. At minus 55 degrees the switch resistance is lower and the losses fall, but the boot capacitor and the output capacitor change value, and a ceramic output capacitor loses most of its capacitance at the cold end, which moves the loop crossover. The vendor specifies the part over the range but the passive components are the customer's choice, so the honest statement is that the regulator is qualified over the range and the board has to be characterised over it.
At the hot end, 125 degrees ambient with a 200 milliohm switch and 0.5 A gives 50 milliwatts of conduction loss before switching, and the 62.5 degrees per watt body raises the junction by about 3 degrees per 50 milliwatts. The switching loss usually dominates at high input voltage, which is why a 48 V to 5 V rail runs hotter than a 12 V to 5 V rail at the same output current.
Where the enhanced part is specified and how to buy it
The typical socket is a housekeeping rail in a downhole tool, an outdoor telecom cabinet or a vehicle system that has to start at minus 40 and keep running at 125 degrees ambient. In those programs the part is usually on an approved parts list by name, and the paperwork, not the price, decides the source. The EP suffix and the MDGQTEP order code should be matched exactly, since the standard part will function on the same board and will not satisfy the temperature requirement.
Our desk treats the enhanced part as a distinct line rather than a variant, so a quote names the temperature grade and the qualification route. Where the enhanced part is short, the alternative is usually a different family in a wider grade rather than a substitution inside the same family, and that comparison is on power management cross reference. For programs that need a documented history of changes, see component obsolescence management and last time buy and LTB planning.
Frequently asked questions
Is the enhanced part a different die. The vendor keeps the same functional description and the same pinout, and states the electrical limits over the wider temperature range. Treat it as the same circuit with a wider specified window, not as a different regulator.
Can the standard part be used at minus 45 degrees. Not within the specification. The standard grade stops at minus 40 ambient, and operation below that is outside the guaranteed range even if a sample works on a bench. That is exactly the case the enhanced product exists for.