Contact Us

TPS51216RUKR

Brand: Texas Instruments
Texas Instruments TPS51216RUKR is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51216RUKR — Power Management & Signal Chain | Superb Automation

TPS51216RUKR

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51216RUKR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51216 complete DDR2, DDR3 and DDR3L memory supply in a 3 mm QFN

The TPS51216RUKR integrates three functions that a DDR memory rail needs: a synchronous buck controller for VDDQ, a 2 A sink and source tracking LDO for VTT, and a buffered low noise reference for VTTREF. It comes in a 20 pin 3 mm by 3 mm QFN and is specified from minus 40 to plus 85 degrees ambient. A board that uses it needs one inductor, one FET pair and the two output capacitor banks, and nothing else to run the memory.

The buck stage takes a conversion voltage from 3 V to 28 V and produces 0.7 V to 1.8 V, which covers DDR2, DDR3 and DDR3L VDDQ. The control loop is D-CAP mode with a selectable 300 kHz or 400 kHz clock, and the auto skip function keeps the light load efficiency up when the memory is idle but the board is awake.

Key parameters taken from the SLUSAB9A document

Conversion input3 V to 28 V, so a 5 V, 12 V or 24 V rail feeds the buck stage directly
VDDQ output0.7 V to 1.8 V, which covers DDR2 at 1.8 V, DDR3 at 1.5 V and DDR3L at 1.35 V
Reference accuracy0.8 % on VREF, and the same 0.8 % on VTTREF tracking of VDDQ divided by two
VTT LDO2 A peak sink and source, with 20 mV accuracy, and 10 microfarad of ceramic output capacitance is enough
Switching frequencySelectable 300 kHz or 400 kHz, which is the choice between efficiency and inductor size
Current limitProgrammable, using low side MOSFET RDS(on) sensing, so no shunt in the power path
ProtectionOvercurrent, overvoltage, undervoltage, UVLO and thermal shutdown, with a power good output
Power statesVTT to high impedance in S3, and soft off of all three rails in S4 and S5
Package20 pin 3.00 mm by 3.00 mm QFN, minus 40 to plus 85 degrees ambient

The three rails and the order they come up in

VDDQ has to be up before VTT can track it, because VTT is defined as VDDQ divided by two. The part handles the sequence internally through the soft start and the tracking loop, but the external enables still decide when the sequence begins. A board that enables VTT ahead of VDDQ will hold the termination at zero until the main rail appears, which is harmless, but a board that disables VDDQ while VTT is still enabled puts the LDO into a state where it sinks current from the termination resistors into a dead rail.

The soft off in S4 and S5 exists for that reason. It discharges all three rails in a controlled order instead of letting the capacitors decide, which is what stops a memory device from seeing a reverse bias on its data pins during a shutdown.

Where the TPS51216 belongs on the board

  • DDR3 and DDR3L memory on industrial control boards with a 24 V input, since the 28 V limit takes the rail directly
  • Networking equipment where the memory bus runs at 1.35 V and the board has only a 12 V feed
  • Medical and test instruments where the power sequence has to be defined and repeatable
  • Embedded computing modules that need one part to cover both the memory core rail and its termination
  • Legacy DDR2 boards that are still in production and need a single source for all three rails

Order code, package and thermal limits

TPS51216RUKR20 pin RUK QFN, 3.00 mm by 3.00 mm, large reel
DissipationThe LDO drops VDDQ divided by two at the termination current, so a 1.5 V memory rail at 2 A puts about 1.5 W in the part and the pad copper decides the temperature
AmbientMinus 40 to plus 85 degrees, so a board in a sealed enclosure needs the thermal calculation done at the enclosure temperature
Dedicated LDO inputA separate LDO supply pin, so the termination can run from a lower rail and the dissipation drops with it

Sourcing notes for this line

This is the part that appears most often on industrial boards that stay in production for a decade, and the supply question is usually about the specific RUK order code rather than the family. The comparison to start from is the power management cross reference, which lists the memory supply parts that share the 20 pin footprint.

Where the exact code is short, the two levers are the DDR generation the board actually needs and the LDO current. A DDR3L board does not need the DDR2 headroom, and the memory cross reference page maps the memory parts to the supplies that support them.

For a long life programme the question is also whether the part will still be produced. The component obsolescence management page covers the last time buy decision for parts on a mature node.

Questions buyers ask about this part

Does it need an external reference? No. The VTTREF output is buffered and low noise, and it tracks VDDQ divided by two at 0.8 % accuracy, so the memory reference pin connects to it directly.

Can the buck stage be skipped? No, and that is the point of the part. If the board already has a 1.5 V rail, a termination only part such as the TPS51206 is the smaller answer.

What is the difference between 300 kHz and 400 kHz? Inductor size against switching loss. At 400 kHz the inductor is smaller for the same ripple, at 300 kHz the efficiency is higher. Both are fixed settings on the same part.

How is the current limit set? By the low side FET RDS(on) and a programming resistor, so the accuracy follows the FET and its temperature coefficient rather than a shunt.