Contact Us

TPS51116MPWPREP

Brand: Texas Instruments
Texas Instruments TPS51116MPWPREP is a power management component designed for AI Servers & Low-Altitude Economy (Drone and UAV) and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

TPS51116MPWPREP — Power Management & Signal Chain | Superb Automation

TPS51116MPWPREP

Texas Instruments — Power Management & Signal Chain

Product Overview

The TPS51116MPWPREP from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

TPS51116-EP complete DDR memory power solution with a 1 A tracking LDO

The TPS51116MPWPREP is the enhanced product version of the TPS51116, a complete DDR, DDR2, DDR3 and LPDDR3 memory power supply in one 20 pin HTSSOP PowerPAD body. It combines a synchronous buck controller for the VDDQ rail, a 1 A sink and source tracking LDO for the VTT termination rail, and a buffered low noise reference for VREF. A memory rail needs all three, and buying them as one part saves the board area and the sequencing logic that three separate devices would need.

The buck controller runs at a fixed 400 kHz pseudo constant frequency with adaptive on time, and it can be configured in D-CAP mode for the fastest load step response or in current mode when the output capacitor bank is all ceramic. The document prints a 100 ns load step response for the D-CAP mode, which is the number that decides whether the rail holds during a memory burst.

Key parameters taken from the SLUSB52A document

Input range3.0 V to 28 V on the buck controller, so a 5 V or a 12 V rail both work, and 24 V systems are covered with margin
VDDQ output2.5 V for DDR, 1.8 V for DDR2, adjustable to 1.5 V for DDR3 or 1.2 V for LPDDR3, with a general range of 0.75 V to 3.0 V
VTT LDO1 A sink and source, tracking VDDQ divided by two, and only 20 microfarad of ceramic output capacitance is needed for stability
ReferenceBuffered, low noise, 10 mA output, 20 mV accuracy on both VREF and VTT
Control modeD-CAP mode with 100 ns load step response, or current mode for all ceramic output banks
Current sensingFrom the low side FET RDS(on) or from a resistor, so a board can trade accuracy for loss
Power statesVTT to high impedance in S3, and soft off of VDDQ, VTT and VREF in S4 and S5
ProtectionPower good, overvoltage, undervoltage, thermal shutdown, and a separate LDO input to cut the LDO dissipation
TemperatureMinus 55 to plus 125 degrees on the enhanced product, marked 51116M on the body
SMD referenceV62/12602-01XE-T, one assembly and test site, one fabrication site, product traceability

What the enhanced product suffix adds for a defence or medical build

The silicon is the same function as the commercial TPS51116, and the difference is in the qualification paperwork. The enhanced product line gives a controlled baseline, one assembly and test site, one fabrication site, a military temperature range of minus 55 to plus 125 degrees, an extended product life cycle, product change notification and traceability to the lot. For a board that is going into a radar power shelf or a medical instrument with a ten year service life, those are the terms that decide whether a part can be used at all.

The practical consequence is that an approved build cannot substitute the commercial grade without a change note, even though the circuit symbol and the pinout are identical. A programme that is short of the enhanced part cannot simply fit the commercial part and keep the same quality record.

Where the TPS51116-EP belongs on the board

  • DDR3 and DDR3L memory banks on defence signal processing cards, where the termination rail has to track VDDQ over temperature
  • Telecom line cards and base station control boards that carry DDR2 or DDR3 memory on a 12 V feed
  • Medical imaging and patient monitoring boards where the memory rail has to come up in a defined order and go down softly
  • SSTL-2, SSTL-18, SSTL-15 and HSTL termination, where the LDO sources or sinks current depending on the data pattern
  • Industrial computers with a 24 V input, since the 28 V input limit leaves headroom for a transient

Order code, package and thermal path

TPS51116MPWPREP20 pin HTSSOP PowerPAD, PWP package, enhanced product, marking 51116M
Thermal pathThe PowerPAD is the only heat path with any real area, so the number of vias from the pad to the ground plane decides the LDO dissipation the board can carry
LDO dissipationThe separate LDO input pin exists so the VTT regulator can run from a lower rail than VDDQ and drop the dissipation, which matters when the memory is at 1.5 V and the feed is 5 V
Output capacitance20 microfarad of ceramic on VTT is enough, so the footprint is two 10 microfarad parts rather than a bank of electrolytics
Absolute maximum1.0 V to 30 V on the switch node, 6 V on the bootstrap, 150 degrees junction

Sourcing notes for this line

Enhanced product parts are made on a single fabrication and assembly site, so their lead time follows that site and not the commercial line. When the enhanced part is not available, the comparison against the commercial TPS51116 is the first thing to run, and the power management cross reference lists which members share the PWP footprint and where they differ.

The second lever is the memory generation. A board built for DDR3 can often move to a controller that also covers DDR3L, which widens the pool of approved parts, and the memory cross reference page sets out which memory parts and which termination schemes go together.

For programmes with a long service life the question is not only the current lead time but whether the part will still be produced in five years. The component obsolescence management page covers the last time buy arithmetic for parts on a controlled baseline.

Questions buyers ask about this part

Is the enhanced part a different silicon? No. It is the same function with a controlled baseline, one site for fabrication and assembly, the military temperature range and product change notification. The electrical limits in the document are what a build is qualified against.

Can VTT be left unloaded? Yes. The LDO is stable with the 20 microfarad of ceramic output capacitance and no load, and it sinks as well as sources, which is what the termination rail needs.

What happens in S3? VTT goes to high impedance and the reference stays alive, which is the state a memory in self refresh needs. In S4 and S5 all three rails are discharged softly.

Does the 100 ns figure apply in current mode? No. The 100 ns load step response is the D-CAP mode number. Current mode is the option for all ceramic output banks and trades some of that response for a loop that is stable without ESR in the capacitor.