Contact Us

INA190A1IDDFR

Brand: Texas Instruments
Texas Instruments INA190A1IDDFR is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA190A1IDDFR — Power Management & Signal Chain | Superb Automation

INA190A1IDDFR

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA190A1IDDFR from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA190A1IDDFR: 25 V/V precision current sense amplifier with 15 microvolt offset

INA190A1IDDFR is a low power, zero drift current shunt monitor with a fixed 25 V/V gain in a SOT-23 body of 8 pins. This is the tighter grade of the low power current sense line: 15 microvolts of offset, 80 nanovolts per C of drift and 132 dB of common mode rejection, all from a 1.7 V to 5.5 V supply that draws 50 microamps. The DDF body carries the REF pin and the enable pin, and the A1 suffix fixes the gain at 25 V/V.

Order code and package

Order codeINA190A1IDDFR
Functionprecision bidirectional current shunt monitor
Gain25 V/V, set by the A1 suffix
PackageSOT-23, 8 pins, 2.90 mm by 1.60 mm
Body optionsSC70 6 pin, SOT-23 8 pin, wafer level 6 ball
Common mode0.2 V below ground to 40 V
Supply1.7 V to 5.5 V
Shutdown current100 nanoamps maximum
Channelsone
Temperature rangeminus 40 to plus 125 C
Gain optionsA1 25, A2 50, A3 100, A4 200, A5 500 V/V
DatasheetSBOS863 revision D, November 2019

Electrical parameters that decide the application

Offset voltage15 microvolts maximum
Offset drift80 nanovolts per C maximum
Gain error0.2 percent maximum on the A1 device
Gain drift7 ppm per C maximum
Common mode rejection132 dB minimum
Quiescent current50 microamps typical at 25 C
Bandwidth45 kHz on A1, falling to 27 kHz on A5
Input bias current500 picoamps typical
Noise75 nanovolts per root hertz referred to the input
Slew rate0.3 volts per microsecond

Points to check before this part goes on a BOM

The 15 microvolt offset is what separates this part from the cost optimised line. On a 10 milliohm shunt it is 1.5 milliamps of reading error, where a 150 microvolt part reads 15 milliamps of error on the same shunt.

The 0.2 percent gain error belongs to the A1 device and not to the whole family. The higher gain options carry a wider gain error in the same document, so a table copied from the front page will overstate the accuracy of an A4 or A5 order code.

Common mode rejection of 132 dB is quoted with the input filter the document specifies. Long leads from the shunt to the amplifier turn that figure into an antenna problem, and a 100 ohm and 22 nanofarad pair at the input is the cheapest way to keep the number.

Shutdown current of 100 nanoamps is a real state on this die, not a datasheet gesture. A battery powered product that leaves the amplifier enabled between samples spends 50 microamps doing nothing, which is more than the sleep current of the microcontroller beside it.

Bandwidth is 45 kHz on this gain option and 27 kHz on the 500 V/V option, so higher gain costs speed. An overcurrent comparator fed from the output has to be rated against the slower figure when the gain option changes late in the project.

The supply minimum of 1.7 V lets the part run from a single cell or from a 1.8 V digital rail, but the output swing stops short of both rails, so a host ADC that measures to the rail will see a dead band at each end that the software has to accept.

Where this order code fits

Boards that need a real accuracy number rather than a coarse trip point, such as server supply telemetry or battery test equipment, are the ones that pay for this grade. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the Medical Device Components page.

Questions buyers ask

Is this the same die as the INA186? The two share the pinout and the package options but not the specification. This part is quoted at 15 microvolts of offset and 132 dB of rejection, while the cost optimised line is quoted at 50 microvolts and 120 dB.

Does the enable pin add a leakage path in shutdown? The maximum shutdown current is 100 nanoamps, so the pin is a genuine disconnect for a battery product, not a low power mode with a hidden floor.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the Supplier Quality Audit page sets out the checks that keep a substitute from failing on the bench.