Contact Us

INA186A1IDDFT

Brand: Texas Instruments
Texas Instruments INA186A1IDDFT is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA186A1IDDFT — Power Management & Signal Chain | Superb Automation

INA186A1IDDFT

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA186A1IDDFT from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA186A1IDDFT: 25 V/V zero drift current sense amplifier with enable in a 8-pin SOT-23

INA186A1IDDFT is a bidirectional current shunt monitor with a fixed 25 V/V gain in a SOT-23 body of 8 pins. The DDF body is the 8-pin version that carries both a REF pin and an ENABLE pin, which the 6-pin SC70 version does not have. It senses across a shunt from 0.2 V below ground to 40 V while running from a 1.7 V to 5.5 V supply, and its 500 picoamp input bias current is what allows microamp measurements through a large shunt.

Order code and package

Order codeINA186A1IDDFT
Functionbidirectional current shunt monitor with enable
Gain25 V/V, set by the A1 suffix
PackageSOT-23, 8 pins, 2.90 mm by 1.60 mm
Pins that matterREF and ENABLE both present only on this DDF body
Common mode0.2 V below ground to 40 V
Supply1.7 V to 5.5 V
Input bias current500 picoamps typical
Channelsone
Temperature rangeminus 40 to plus 125 C
Gain optionsA1 25, A2 50, A3 100, A4 200, A5 500 V/V
DatasheetSBOS318 revision B, July 2021

Electrical parameters that decide the application

Offset voltage50 microvolts maximum
Offset drift0.5 microvolts per C maximum
Gain error1 percent maximum
Gain drift10 ppm per C maximum
Common mode rejection120 dB minimum
Quiescent current48 microamps typical, 90 microamps maximum
Bandwidth45 kHz on A1, falling to 27 kHz on the 500 V/V A5 option
Noise75 nanovolts per root hertz referred to the input
Slew rate0.3 volts per microsecond
Shutdown currentunder 1 microamp with ENABLE low

Points to check before this part goes on a BOM

The 500 picoamp bias current is the reason this part can measure microamps at all. A 1 kiloohm shunt with a 10 nanoamp leakage from a cheaper amplifier would read 10 microvolts of error, which is a fifth of this part's whole offset budget.

Bandwidth falls with gain, and the fall is not a rounding error. The A1 device holds 45 kHz while the A5 device holds 27 kHz, so a board that needs the 500 V/V option and a fast overcurrent trip is trying to use two ends of the same trade at once.

The offset budget of 50 microvolts is fixed, so the shunt sets the usable resolution. At 25 V/V with a 10 milliohm shunt, 50 microvolts is 5 milliamps of reading error, and the same part on a 1 ohm shunt reads microamps but dissipates real power.

ENABLE sits only on this 8-pin body and on the wafer level package. A board that has to keep a measurement chain dark during sleep should confirm the pin in the footprint, because the 6-pin SC70 body has no enable and its quiescent current is always on.

The REF pin sets the zero current point exactly the way it does on the rest of the family. Bidirectional sensing in a battery charger needs that pin driven from a low impedance reference, not from a resistor divider that moves with temperature.

Thermal drift of the offset is 0.5 microvolts per C, which is 75 microvolts across the full range. That is above the 50 microvolt initial offset, so a unit calibrated cold and then run hot will move more than the datasheet first line suggests.

Where this order code fits

Battery chargers, notebook power paths and server supplies are the boards that ask for this order code, usually because the rail is below 2 V and the leak has to stay in the microamp range. Boards comparing it with a neighbouring part start from our Amplifier Cross Reference page, and boards replacing a part that has gone end of life start from the One Stop BOM Sourcing page.

Questions buyers ask

Is the 8-pin body pin compatible with the 6-pin part? No. The DDF body adds REF and ENABLE, so the footprint and the pin count both differ from the SC70 part.

Can it sit on a 1.8 V rail? Yes. The minimum supply is 1.7 V, and the common mode range stays independent of that supply.

SUPERB holds and sources this Texas Instruments line for production and repair demand, quoted against the exact ordering string with date codes, packing and country of origin stated on the offer. When a line is moving, the How to Verify a Drop in Replacement page sets out the checks that keep a substitute from failing on the bench.