INA143U
Product Specifications
INA143U
Texas Instruments — Power Management & Signal Chain
Product Overview
The INA143U from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-efficiency power conversion with low quiescent current
- Wide input voltage range with precision output regulation
- Integrated over-current, over-temperature, and short-circuit protection
- Small footprint packaging for space-constrained designs
- AEC-Q100 qualified options available for automotive applications
- Flexible sequencing and soft-start control
Key Specifications
| Input Voltage | V |
| Output Voltage | V |
| Output Current | A |
| Switching Frequency | kHz |
| Efficiency | % |
| Quiescent Current | µA |
| Topology | — |
| Package | — |
| Operating Temp | °C |
| Protection | — |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
INA143U: gain of 10 from a trimmed network, eight pin SOIC
INA143U is a difference amplifier with a laser trimmed 10 kohm and 100 kohm network on each input, a fixed gain of 10 V/V, and a U grade offset window of 250 microvolts. It is the cheapest way to buy a matched resistor network and an op amp in one body, and the reason people do it is that four discrete 0.1 per cent resistors cost more and track worse.
What the part is not is flexible. The gain is 10 or 0.1 and nothing between, the input impedance is 20 kohm differential, and the supply current is 950 microamps. A channel that needs a gain of 50, or a source impedance above a few kiloohms, is looking at another member of the family, and the programmable gain part is the one that covers it.
INA143U as the vendor document publishes it
| Gain | 10 V/V, or 0.1 V/V with input and reference exchanged |
| Gain error | 0.01 per cent typical, 0.05 maximum |
| Gain drift | 1 ppm per degree typical, 10 maximum |
| Nonlinearity | 0.0001 per cent typical, 0.001 maximum of full scale |
| Offset | 100 microvolts typical, 250 maximum |
| Offset drift | 1 microvolt per degree typical, 3 maximum |
| Common mode rejection | 86 dB minimum, 96 typical at plus or minus 14.85 volts |
| Input impedance | 20 kohm differential, 55 kohm common mode |
| Voltage noise | 27 nanovolts per root hertz at 1 kHz, 45 at 10 Hz |
| Bandwidth | 0.15 MHz small signal |
| Slew rate | 5 volts per microsecond |
| Settling to 0.01 per cent | 9 microseconds on a 10 V step |
| Overload recovery | 6 microseconds from a 50 per cent overdrive |
| Output swing | within 1.3 volts of the positive rail into 10 kohm |
| Quiescent current | 950 microamps typical, 1.2 milliamps maximum |
| Supply range | plus or minus 2.25 to plus or minus 18 volts, 4.5 to 36 single |
| Current limit | 25 milliamps sinking, 32 sourcing |
| Stable load capacitance | 1000 picofarads |
| Body | eight pin SOIC |
| Temperature range | minus 40 to plus 85 degrees, operation to plus 125 |
| Catalogue code | INA143U |
| Grade | U, 250 microvolts maximum offset |
| Network | 10 kohm and 100 kohm per input, laser trimmed |
Gain of 10 from a network that tracks on the die
INA143U is a difference amplifier with a 10 kohm and a 100 kohm resistor on each input, laser trimmed to a gain of 10 V/V with a gain error of 0.01 per cent typical and 0.05 per cent maximum on the U grade, 0.1 per cent on the UA grade. The ratio, not the absolute value, sets the gain, and the ratio holds because both resistors sit on the same die and move together with temperature at 1 ppm per degree typical and 10 maximum.
That is the argument for buying the function rather than building it. Four discrete 0.1 per cent resistors with 25 ppm tracking cost more board area and more test time, and they do not track as well because they are four separate parts at four temperatures. What the integrated network gives up is flexibility: the gain is 10 or 0.1 and nothing between, and the input impedance is fixed at 20 kohm differential and 55 kohm common mode.
27 nanovolts per root hertz into a 20 kohm load
The noise of INA143U is 27 nanovolts per root hertz at 1 kHz, 30 at 100 Hz, 45 at 10 Hz and 1 microvolt peak to peak from 0.1 to 10 Hz, all referred to the input. On a 1 kohm source that is the dominant term and the amplifier is quiet. On a 10 kohm source the resistor noise alone is 12.8 nanovolts per root hertz, so the part adds about twice the source noise, and on a 100 kohm source the source dominates and the amplifier choice stops mattering.
The load is the other half of the same paragraph. With 20 kohm differential across the input, a 1 kohm source impedance loses 5 per cent of the signal in the divider, which is five hundred times the 0.01 per cent gain error and has to be calibrated or buffered. The loading also converts any imbalance between the two source resistances into a differential error, so a protection resistor added to one input has to be added to the other in the same value.
950 microamps and 5 volts per microsecond
INA143U draws 950 microamps typical and 1.2 milliamps maximum per amplifier, which is high for a difference amplifier and is the price of the 5 volt per microsecond slew rate and the 3 MHz gain bandwidth that the family is sold on. Settling is 6 microseconds to 0.1 per cent and 9 microseconds to 0.01 per cent on a 10 V step with a 100 pF load, and overload recovery from a 50 per cent overdrive is 6 microseconds.
The supply current matters in two places. In a battery instrument 1.2 milliamps is a large share of the budget, and the part is then only justified when the signal is fast. In a rack instrument it is irrelevant and the slew rate is what allows a multiplexed channel to be scanned quickly. The 3 MHz figure is a small signal number; a 10 V step at 5 volts per microsecond takes 2 microseconds before settling even begins, so the settling row is the one to use for a scan budget.
Plus or minus 2.25 to 18 volts, output to within 1.3 volts
The supply window on INA143U is plus or minus 2.25 to plus or minus 18 volts, or 4.5 to 36 volts single, and the output swings to within 1.3 volts of the positive rail and 0.8 volts of the negative into a 10 kohm load. Into 100 kohm the figures improve to 0.8 and 0.3 volts. Current limit is 25 milliamps sinking and 32 sourcing, continuous into the common point, and the part is stable into 1000 picofarads.
On a single 5 V rail the output window is therefore about 1.9 to 3.7 volts, which is narrow but usable for a 2.5 V referenced signal. The common mode range, by contrast, extends beyond both rails: the positive limit is 1.1 times the positive rail minus 1 volt and the negative limit 1.1 times the negative rail plus 1 volt, both measured with the output at zero. That asymmetry is what lets the part sit on a high side shunt above its own supply.
A gain of 0.1 from the same four resistors
The same network that gives INA143U a gain of 10 gives 0.1 when the input and the reference are exchanged, which is the configuration for attenuating a high differential voltage to the window of a converter. A plus or minus 100 V differential becomes plus or minus 10 V at the output, and the common mode that comes with it is rejected by the same 86 dB typical, 96 dB typical on the U grade at plus or minus 14.85 volts.
Attenuation changes the noise arithmetic: the 27 nanovolts per root hertz is referred to the input, so at a gain of 0.1 it is 2.7 nanovolts at the output and the resistor network noise dominates instead. It also changes the overload behaviour, because the input can sit far outside the supply while the output stays inside its window. That is the configuration used for a differential line receiver or a synchronous demodulator front end, and it is why the family lists both gains on the first page.
The SO-8 body and what the two grades buy
INA143U is the eight pin SOIC, the single version of a pair whose dual member is the INA2143 in a fourteen pin body. The U grade carries 250 microvolts maximum offset, 3 microvolts per degree maximum drift and 0.05 per cent maximum gain error; the UA grade carries 500 microvolts, drift from the typical curve rather than a limit, and 0.1 per cent gain error. Both are specified over minus 40 to plus 85 degrees and both operate to plus 125 with derating.
The grade decision is arithmetic. Five hundred microvolts of offset at a gain of 10 is 5 millivolts at the output, which on a 2 V span is 0.25 per cent and has to be trimmed. Two hundred and fifty microvolts halves that and costs the difference in unit price. Neither grade is laser trimmed after packaging, so the drift, not the initial offset, is what a production calibration cannot remove, and the UA grade publishes its drift as a curve rather than as a limit, which is the reason a channel that runs hot tends to be specified on the U grade.
The eight pin SOIC is the whole carrier story on this family, and tube or reel is a quantity decision rather than an electrical one. Our BOM scrubbing page covers matching the code on the board to the code on the reel, and the amplifier cross reference page covers the candidates when the U grade is not on the shelf.
Can the gain be changed to 5 with an external resistor? No. The network is inside the package and the gain is a ratio of two on-die resistors; there is no gain pin. A gain of 5 needs a different part.
Is the 3 MHz bandwidth real? The family sells the part on speed, and the specification table quotes 0.15 MHz small signal with 5 volts per microsecond of slew rate. A 10 V step at 5 volts per microsecond takes 2 microseconds before settling starts, so the 9 microsecond settling row is the one to use in a scan budget.