Contact Us

INA137UA

Brand: Texas Instruments
Texas Instruments INA137UA is a power management component designed for Industrial Automation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

INA137UA — Power Management & Signal Chain | Superb Automation

INA137UA

Texas Instruments — Power Management & Signal Chain

Product Overview

The INA137UA from Texas Instruments is a power management / signal chain IC delivering high efficiency, precision regulation, and robust protection. Texas Instruments (TI) is a global leader in analog ICs, power management solutions, and embedded processors.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-efficiency power conversion with low quiescent current
  • Wide input voltage range with precision output regulation
  • Integrated over-current, over-temperature, and short-circuit protection
  • Small footprint packaging for space-constrained designs
  • AEC-Q100 qualified options available for automotive applications
  • Flexible sequencing and soft-start control

Key Specifications

Input VoltageV
Output VoltageV
Output CurrentA
Switching FrequencykHz
Efficiency%
Quiescent CurrentµA
Topology—
Package—
Operating Temp°C
Protection—

Applications

Industrial Automation Automotive Electronics Telecom Infrastructure Server & Data Center Power Medical Devices Consumer Electronics

Request Quote — In Stock, 100% New & Original, Full Warranty

INA137UA: a minus 6 dB audio line receiver in an eight pin SOIC, in a 75 piece tube

The INA137UA is a differential line receiver with a fixed 6 dB of attenuation, 0.5 V/V, in an eight pin SOIC and a 75 piece tube. The on-chip network is 12 kΩ and 6 kΩ, trimmed as a set, and the same network can be wired for a gain of 2 by reversing the input and feedback connections as the vendor shows. It is the pad down member of a group of three: 0.5, 1 and 2 V/V from the same topology.

The audio rows are a step better than the unity gain part: minus 106 dBu of noise floor referred to the output, 0.0005 per cent of distortion at 1 kHz, plus 23 dBu of headroom, 4 MHz of small signal bandwidth, 14 V per microsecond of slew and 123 dB of channel separation on the dual. Each channel draws 2.9 mA maximum on plus or minus 4 V to plus or minus 18 V.

The INA137UA rows as the addendum publishes them

Part classAudio differential line receiver, fixed minus 6 dB, trimmed 12 kΩ and 6 kΩ network
Vendor statusActive, production
Data sheetPDS-1391B, Burr-Brown, July 1997
Addendum rowINA137UA, 75 pieces per tube
Gain0.5 V/V, minus 6 dB, with a gain of 2 configuration by reversing the input and feedback connections
Gain error0.1 per cent maximum, 0.01 typical
Gain nonlinearity0.0001 per cent of full scale
Total harmonic distortion plus noise0.0005 per cent at 1 kHz
Noise floorMinus 106 dBu referred to the output
HeadroomPlus 23 dBu
Input offset voltage1 mV maximum referred to the output
Common mode rejection90 dB typical at a plus or minus 46.5 V common mode
Input impedance24 kΩ differential, 18 kΩ common mode
Bandwidth4 MHz small signal
Slew rate14 V per microsecond
OutputPlus or minus 16 V, 500 pF stable, 60 mA
Supply rangePlus or minus 4 V to plus or minus 18 V
Quiescent current2.9 mA maximum per amplifier
BodySOIC, D outline, 8 pins
Moisture levelLevel 3, 260 degrees, 168 hour floor life

Minus 6 dB, and the two ways the network is wired

INA137UA is a differential line receiver with a fixed 6 dB of attenuation, 0.5 V/V, set by the on-chip 12 kohm and 6 kohm resistors. The same network can be wired for a gain of 2, which the vendor shows as a receiver with the input and feedback resistors reversed; the resistors do not change, only which pins the signal and the reference reach. That is why one part covers both a pad down and a pad up function, and why the pin connection has to be read before the gain is assumed.

For unity gain the vendor points to the INA134 instead, so the three parts in this group cover 0.5, 1 and 2 V/V with the same topology. Gain error on INA137UA is 0.1 per cent maximum and gain drift is 1 ppm per degree, so the 6 dB is accurate to a hundredth of a decibel before the source impedance is considered. The network is ratio matched but its absolute value carries 25 per cent tolerance on the older sheets.

A noise floor of minus 106 dBu on a line receiver

The audio rows on INA137UA are a step better than the unity gain sibling: total harmonic distortion plus noise is 0.0005 per cent at 1 kHz with a 10 V rms input, the noise floor is minus 106 dBu referred to the output over 20 kHz, and the headroom is plus 23 dBu. The output noise over the audio band is 3.5 microvolts rms against 7 on the INA134, because the 6 dB of attenuation is applied before the amplifier sees the signal.

That is the trade the part makes: 6 dB of level is given away at the input and 6 dB of noise performance is gained at the output, so a plus 23 dBu line arrives at the converter at plus 17 dBu with the same signal to noise ratio as the unity gain part and twice the headroom margin. On a broadcast chain where the nominal level is plus 4 dBu and the peaks are plus 20, the attenuation is what keeps the amplifier out of clipping.

24 kohm differential and 18 kohm common mode across the source

The input network of INA137UA presents 24 kohm differential and 18 kohm common mode, lower than the unity gain part because the 12 kohm and 6 kohm resistors sit in a different ratio. Across a 50 ohm line that is a 0.2 per cent loading error, which the 0.1 per cent gain error row already covers; across a 10 kohm source it is a 30 per cent divider and the channel has to be recalibrated.

Lower impedance also means the network dominates the noise at ordinary source impedances, which is why the noise row is specified with the network included. On a 600 ohm line the thermal noise of 24 kohm is about 20 nanovolts per root hertz, four times the 26 nanovolts per root hertz the sheet quotes at 1 kHz when the source is zero. The line impedance, not the amplifier, sets the noise floor of an installed system.

Plus or minus 46.5 V of common mode and 90 dB of rejection

Common mode rejection on INA137UA is 90 dB typical and 74 dB minimum at a plus or minus 46.5 V common mode with the source at zero ohms, and the input common mode range extends to three times the supply minus seven and a half volts in each direction. On plus or minus 18 V that is plus or minus 46.5 V, so a chassis difference of tens of volts is inside the window rather than outside it. The absolute maximum input is 80 V.

Rejection is the entire function of the part, and it is a ratio match measurement: the two input paths have to see the same impedance. A 1 kohm imbalance in a 24 kohm network is a 4 per cent mismatch and the 90 dB becomes 28 dB, which is audible hum at mains frequency. The specification assumes the source is balanced, and a line receiver is only as good as the cable and the connectors in front of it.

2.9 mA, plus or minus 4 to 18 V, and 150 degrees per watt

Each channel of INA137UA draws 2.4 mA typical and 2.9 mA maximum over a supply window of plus or minus 4 V to plus or minus 18 V, with an absolute maximum of 40 V total. The eight pin SO-8 has a junction to ambient figure of 150 degrees per watt against 100 for the DIP, so about 100 milliwatts per channel raises the junction 15 degrees in the surface mount body. The specified range is minus 40 to plus 85 and the operating range minus 55 to plus 125.

The output swings to within 1.8 V of the positive rail and 1.6 V of the negative rail, which on plus or minus 18 V is plus or minus 16 V or plus 26 dBu, and the continuous output current is 60 mA into a 600 ohm load. Load capacitance is limited to 500 pF, so a cable needs a series resistor of 47 to 100 ohms at the output, and the part is stable into that arrangement.

1 mV referred to the output, and the two gain configurations of one network

Input offset on INA137UA is 1 mV maximum referred to the output with a 2 microvolt per degree drift, and the offset is referred to the output because the gain is 0.5. At the output the 1 mV is 1 mV; at the input it is 2 mV, which is what an installer measuring at the connector would see. Long term stability is not quoted on this sheet, and the power supply rejection is 60 microvolts per volt maximum over the plus or minus 4 to plus or minus 18 V window.

The ordering rows are simple: INA137UA is a 75 piece tube at moisture level 3, and the 2500 piece reel is the same part under the slash 2K5 suffix. The dual INA2137UA is the fourteen pin SOIC at 50 pieces per tube or 2500 on a reel, with 123 dB of channel separation at 1 kHz, which is why a stereo pair goes into one package rather than two singles.

Buying INA137UA

This is the part for a plus 4 dBu nominal line that can peak at plus 20, because 6 dB of attenuation puts the peak at plus 14 at the amplifier and leaves room for a transient. The unity gain INA134 is the part for a lower level line, and choosing between them is a level plan question rather than a performance question.

Both the tube and the reel are active, so the carrier is a convenience rather than a constraint. The grade question does not arise because there is only one grade, and the offset of 1 mV referred to the output is the same on every row. Our incoming inspection plan page covers the receipt checks for an audio part where a counterfeit relabel is hard to see.

Questions that arrive with this part number

Whether the part can be used at a gain of 2 is the first question, and it can, by reversing the input and feedback connections as the vendor figure shows; the resistors do not change, which is why one part covers two functions. The second is whether it can replace the INA134, and it cannot without a level change, because 6 dB of attenuation is the difference between them.

The third is the input impedance, 24 kΩ differential and 18 kΩ common mode, lower than the unity gain part and therefore a heavier load on a 600 ohm line, though still not a significant one. The fourth is the common mode range, three times the supply minus 7.5 V, which on plus or minus 18 V is plus or minus 46.5 V and covers any chassis difference a studio can produce.